TL-SG2428P v4 switch keep dropping PoE ports

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TL-SG2428P v4 switch keep dropping PoE ports

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TL-SG2428P v4 switch keep dropping PoE ports
TL-SG2428P v4 switch keep dropping PoE ports
2023-03-21 10:57:20
Model: TL-SG2428P  
Hardware Version: V4
Firmware Version: 4.0.5 Build 20221130 Rel.42340

I have a TL-SG2428P v4, latest firmware on all devices and latest virtual Omada controller.  This switch has 2 ports with PoE enabled and these ports will 'go down' randomly.  The only remedy is to reboot the switch.

 

Any advice on what might be causing this?

 

 

  0      
  0      
#1
Options
5 Reply
Re:TL-SG2428P v4 switch keep dropping PoE ports
2023-03-22 03:44:35

Hello @Jacko_ ,

 

Did this issue start to happen when you deploy the switch for the first time?

What is the status of the POE light when the port goes down?

Do all POE ports have the same issue?

 

May I know the model number of the PD device?

It is advisable to use different Ethernet cables for the test. The shorter, the better.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#2
Options
Re:TL-SG2428P v4 switch keep dropping PoE ports
2023-03-22 17:33:20

  Hi @Hank21

 

Thanks for your reply.

 

No it's just a recent issue, the switch up until now has been fine.

 

When the issue occurs the port goes from green to grey to indicate nothing is attached.  Unplugging and plugging the AP back in doesn't resolve the issue.  All PoE devices have the same issue at the same time when connected to TL-SG2428P, so it seems as though it's a power issue.  I have two other EAP610 APs connected to a Netgear switch which is faultless.

 

Omada Controller v5.9.31 - running on a Windows VM

ER605     v2.0        2.1.2 - connected to the below Netgear PoE switch
TL-SG2428P v4.0        4.0.5
EAP610    v2.0        1.0.2 - connected to Netgear PoE switch (no issue with this one)
EAP610    v2.0        1.0.2 - connected to Netgear PoE switch (no issue with this one)
EAP610    v2.0        1.0.2 - connected via 5 meter pure copper Cat5e run
EAP225-Outdoor     v1.0    5.0.9 - was connected via .5 patch cable

 

 

 

 

  0  
  0  
#3
Options
Re:TL-SG2428P v4 switch keep dropping PoE ports
2023-03-23 02:40:07

Hi @Jacko_ ,

 

Thank you so much for taking the time to post the issue on the TP-Link community!

 

To better assist you, I've created a support ticket via your registered email address, and escalated it to our support engineer to look into the issue. The ticket ID is TKID230339416, please check your email box and ensure the support email is well received. Thanks!

Once the issue is addressed or resolved, welcome to update this topic thread with your solution to help others who may encounter the same issue as you did.

 

Many thanks for your great cooperation and patience!

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#4
Options
Re:TL-SG2428P v4 switch keep dropping PoE ports
2023-03-23 09:07:37

  @Hank21 

 

Thanks for logging the support ticket.  I have replied to the email with the log file requested.

  0  
  0  
#5
Options
Re:TL-SG2428P v4 switch keep dropping PoE ports
2023-03-24 01:04:38

Hello  @Jacko_,

 

That's great! Please feel free to reply to the support email for further follow-up.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 1001

Replies: 5

Related Articles