ER605 disconnected from OC200
updated my ER605 v6 to latest firmware and after an hour or so it disconnects from the controller
both are on the latest firmware
ER605_V2_2.2.0 Build 20230629
OC200(UN)_V2/V2.6_2.9.3 Build 20230328
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi All,
A newer 2.1.4 Beta firmware has been released for trial, please follow the post link below for details.
ER605 V2_2.1.4_Build 20230720 Beta Firmware For Trial (Released on July 21st, 2023)
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
In the meantime, would you please provide the following information?
1. What's your WAN connection type? Are you using an ADSL modem? If not, please specify it.
2. Is your topology as simple as Modem---Router---Controller+Devices?
3. What is your Controller version? Please specify its full version. If you are using the beta, please let me know.
What is your ER605 firmware version before your upgrade? (From what version did you upgrade to official V2.2.0?)
Thanks for your cooperation!
- Copy Link
- Report Inappropriate Content
Thank you so much for taking the time to post the issue on TP-Link community!
To better assist you, I've created a support ticket via your registered email address, and escalated it to our support engineer to look into the issue. The ticket ID is TKID230717103, please check your email box and ensure the support email is well received. Thanks!
Once the issue is addressed or resolved, welcome to update this topic thread with your solution to help others who may encounter the same issue as you did.
Many thanks for your great cooperation and patience!
- Copy Link
- Report Inappropriate Content
Clive_A wrote
In the meantime, would you please provide the following information?
1. What's your WAN connection type? Are you using an ADSL modem? If not, please specify it.
2. Is your topology as simple as Modem---Router---Controller+Devices?
3. What is your Controller version? Please specify its full version. If you are using the beta, please let me know.
What is your ER605 firmware version before your upgrade? (From what version did you upgrade to official V2.2.0?)
Thanks for your cooperation!
Hi @Clive_A,
- My (Hardware-)Controller is Version 2.9.3 Build 20230328 Rel.52390
- I Upgraded the ER605 V2 from Version 2.1.2 Build 20230210 Rel.62992 to the V2.2.0
- The topology is: (Cable-)Modem -> ER-605 -> TL-SG2008P v3.0 (3.0.5) -> OC-200 v2.0 (2.9.3)
- Instead of an ADSL-Modem i am using DOCSIS-Modem in Bridge-Mode
- the ER-605 is configured to use the WAN-Port with the "Dynamic IP" (IPv4) and "Dynamic IP (SLAAC/DHCPv6)" (IPv6) Connection Types.
- Copy Link
- Report Inappropriate Content
Thank you so much for taking the time to post the issue on TP-Link community!
To better assist you, I've created a support ticket via your registered email address, and escalated it to our support engineer to look into the issue. The ticket ID is TKID230717074, please check your email box and ensure the support email is well received. Thanks!
Once the issue is addressed or resolved, welcome to update this topic thread with your solution to help others who may encounter the same issue as you did.
Many thanks for your great cooperation and patience!
- Copy Link
- Report Inappropriate Content
OC200v2 5.9.32
ER605v2 downgraded back to 2.1.3 beta to stop the issue
i have dual wan DSL modem/ 5G Gateway
i had upgraded from 2.1.3 beta to the final 2.2.0 then the issue started
- Copy Link
- Report Inappropriate Content
about this tcp flag, it is not a danger. i remember it's a minor fault in the triggering mechanism. you can turn it off
https://community.tp-link.com/en/business/forum/topic/610802
- Copy Link
- Report Inappropriate Content
Hi All,
A newer 2.1.4 Beta firmware has been released for trial, please follow the post link below for details.
ER605 V2_2.1.4_Build 20230720 Beta Firmware For Trial (Released on July 21st, 2023)
- Copy Link
- Report Inappropriate Content
Information
Helpful: 2
Views: 1129
Replies: 9