Static Routing with TL-R480T (over WiFi)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Static Routing with TL-R480T (over WiFi)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Static Routing with TL-R480T (over WiFi)
Static Routing with TL-R480T (over WiFi)
2023-09-22 16:21:42 - last edited 2023-11-10 06:26:55
Model: TL-R480T+   RE650  
Hardware Version: V9
Firmware Version:

Hello everyone,

Is there anyone here who can help me set up the static routing on my TL-R480T?

I really have no idea how to do that.

I've only ever had one Fritzbox. Since our internet connection was no longer sufficient for me, I also got internet via SkyDSL. (That's only for me ^^)

Of course I also got new hardware for this.

Since I only want to use SkyDSL on my laptop, I also needed a solution on how I could access my existing Fritzbox network using the network from the SkyDSL router.

So I got the TL-R480T+.

I also bought the RE650, which I use as an access point.

A (long) network cable went from my Fritzbox to my Proxmox server. (This has the fixed IP 192.168.178.101)

All my containers and VMs are built on this network.

I set this statically in /etc/network/interfaces.

My SkyDSL router has the IP 192.168.1.1 (But I think that doesn't matter at this point)

My TP-Link (192.168.0.1) gave me the IP 192.168.0.115 on my Macbook.

How can I continue to access the Fritzbox network with my laptop? That will have something to do with “static routing”. But I can't get it.

I don't know what I should enter/select for Destination IP, Subnet Mask, Next Hop or Interface.

My setup looks like this.

WAN 1 == SkyDSL router

WAN/LAN 2 == Fritzbox

WAN/LAN 3 == FREE (unoccupied)

WAN/LAN 4 == RE650

LAN 5 == Proxmox

 

I hope I was able to explain everything to you the way I imagine it.
If you need to know anything else, please ask.
It's very important to me that it finally works.

  0      
  0      
#1
Options
1 Reply
Re:Static Routing with TL-R480T (over WiFi)
2023-09-25 03:22:35 - last edited 2023-11-10 06:26:28

Hi @MrThiemann 

Thanks for posting in our business forum.

So, first, answer your question about static routing: How to configure Static Routing on wireless routers

I am pasting this to help you understand static routing. The static routing is pretty much the same on any router. Since the User Guide has shown the use and steps, you can refer to the User Guide for detailed information.

 

Second, you seem to know what to do with static routing. So, I've pointed out what you should configure and how by the FAQ or the User Guide. So you should have a basic ideal on "how-to".

But I'll just tell you what should be happening in a normal scenario.

If you are connected like this, then they are in two separate networks. Two NATs are creating two different local area networks, AKA LAN.

MrThiemann wrote

My SkyDSL router has the IP 192.168.1.1 (But I think that doesn't matter at this point)

My TP-Link (192.168.0.1) gave me the IP 192.168.0.115 on my Macbook.

How can I continue to access the Fritzbox network with my laptop? That will have something to do with “static routing”. But I can't get it.

I don't know what I should enter/select for Destination IP, Subnet Mask, Next Hop or Interface.

My setup looks like this.

WAN 1 == SkyDSL router

WAN/LAN 2 == Fritzbox

WAN/LAN 3 == FREE (unoccupied)

WAN/LAN 4 == RE650

LAN 5 == Proxmox

My opinion: static routing is not gonna be helpful anyway to access the Fritzbox network.

 

A normal scenario:

If your network is like ISP----Router A----PC A & Router B----PC B. From the PC B, you should be able to access the PC A and Router A. You can access their LAN(from Router A) IP addresses, but PC A cannot access PC B unless you port forward.

In your setup, if you want to force certain devices to go through WAN/LAN2 for Internet access, you should use Policy Routing instead of Static Routing.

 

Same, you still need to port forward, to allow access from Fritzbox to the R480T+. You should use Policy Routing to force traffic to go through WAN/LAN2. But I don't understand what you mean by accessing the Frtizbox network. Policy Routing should do it. Like described above, you should have access to the PC A and Router A if you are connected in that way, which is pretty much the same as your current setup.

 

If you want others to help you more, you should be more specific. So far, that's my assumption and first reaction.

Best Regards! If you are new to the forum, please read: Howto - A Guide to Use Forum Effectively. Read Before You Post. Look for a model? Search your model NOW Official and Beta firmware. NEW features! Subscribe for the latest update!Download Beta Here☚ ☛ ★ Configuration Guide ★ ☚ ☛ ★ Knowledge Base ★ ☚ ☛ ★ Troubleshooting ★ ☚ ● Be kind and nice. ● Stay on the topic. ● Post details. ● Search first. ● Please don't take it for granted. ● No email confidentiality should be violated. ● S/N, MAC, and your true public IP should be mosaiced.
  0  
  0  
#2
Options

Information

Helpful: 0

Views: 527

Replies: 1

Related Articles