Business Community > All Threads > EAP690E HD(EU) v1.0 POE Issues
< All Threads

EAP690E HD(EU) v1.0 POE Issues

EAP690E HD(EU) v1.0 POE Issues

EAP690E HD(EU) v1.0 POE Issues
EAP690E HD(EU) v1.0 POE Issues
2024-08-27 06:48:46
Tags: #Installation #Network Connectivity
Model: EAP690E HD  
Hardware Version: V1
Firmware Version: 1.0.1 Build 20221114 Rel. 62130

Hello,

I have a strange issue with the mentioned AP. After a power loss for example the AP will not boot up correctly via PoE. It starts provisioning and then disconnects and is shown offline in the controller. I have to disconnect and reconnect it several times. Sometimes the AP will then start working again. If not i have to completely hard reset it and re-adopt it from scratch. After that it works completely fine until the next power loss.

 

Things I tried already:

- new cables

- shorter cables

- PoE injector

 

My Hardware setup is:

Switch: SX3206HPP v1.20

Cable: 10M CAT 10 Network cable

AP: EAP690E HD(EU) v1.0

 

I wonder if i bought just the wrong AP because it seems other APs just work fine.

  0      
 
  0      
 
#1
Options
3 Reply
Re:EAP690E HD(EU) v1.0 POE Issues
2024-08-28 09:57:45 - last edited 2024-08-28 10:01:23

  @Florian-T 

Do you test other APs in the same location as this one? Also, do you make sure there is enough power to this AP? What is the frequency of the drop? The unit seems to consistently lose power.So, it is quite unstable?

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#2
Options
Re:EAP690E HD(EU) v1.0 POE Issues
Wednesday
I have 2 EAP783 on the same switch which is a SX3206HPP v1.20 This switch has a power budget of 200W according to the specs. The other EAPs are working fine. The EAP690E HD is not working after a reboot of the switch. After several trials it starts to work again after tedious fiddling. I do not understand what the problem is because the switch supports 802.3af/at/bt PoE++ which is needed for the EAP690E HD.
  0  
  0  
#3
Options
Re:EAP690E HD(EU) v1.0 POE Issues
Wednesday
Also in addition: I have to forget the device and re-adopt it with a powersupply connected. I have to do this 2-3 times until successful. Then i can reconnect it the old way on the place with the cable it always had and it just works fine with PoE++ until the next reboot.
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 212

Replies: 3

Tags

Installation Network Connectivity
Related Articles
EAP690E HD 5GHz radios, why no 160MHz channel width?
679 1
Where did the IPv6 support go in the EAP690E HD?
1335 0
IPv6 EAP690E (and EAP670)
2240 4
EAP690 HD no 2,4Ghz wifi available
430 0
EAP690E HD works best with TL-SG3210XHP-M2 V2
320 0
EAP690E HD and 5.12.9 don't mix
890 4
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.