5G/4G Wi-Fi Routers/MiFi

You can share your 5G/4G network with multiple Wi-Fi devices by using TP-Link 5G/4G Wi-Fi Routers or MiFi products. Share your story and join the discussion with other users here.
5G/4G Wi-Fi Routers/MiFi

Tags

Label

 
If you have experienced an issue of disconnecting or slowness on the 4G Wi-Fi router’s network due to the auto band selection, Please download and install the following beta firmware on the router to
Highlighted ThreadOfficialBand Selection
By Kevin_Z · Latest post 6 hours ago by dan2025
158Helpful
163174Views
316Replies
Does someone knows which bands are supported for external antennas for this modem Archer NX200? Cannot find in anywhere. Thanks.
Band SelectionAntennas
By smoger · Latest post 2 weeks ago by Silverek
11Helpful
3039Views
9Replies
may i know what lte band for redone is best cause i just get 10mbps only better redone setting
Network ConnectivityBand Selection
By kx99 · Latest post 2025-03-31 03:09:47 by Marvin_S
0Helpful
132Views
1Replies
The crux of the question is: Does the Archer NX600 have Carrier Aggregation? And for someone in an area with bad reception, would the NX200 and the NX600 perform the same to improve signal from 4G LTE
Network ConnectivityMobile Wi-FiCarrier AggregationBand Selection
By peullywo0s · Latest post 2025-03-28 06:01:08 by Marvin_S
0Helpful
320Views
1Replies
Hello, I recently purchased an MR505 and very quickly noticed some frequent "disconnections". The router tells me everything is fine, but no Internet traffic goes through. After disabling every servic
Band SelectionCarrier AggregationNetwork Connectivity
By GreenSkol · Latest post 2025-03-18 09:14:28 by Marvin_S
1Helpful
153Views
1Replies
Country: Italy SIM Operator: Iliad Issue 1: I have been using the Archer NX200 router for two months. During the first month, the router connected correctly to the 5G NSA network, providing good downl
Firmware UpdateBand SelectionNetwork Connectivity
By ahbello · Latest post 2025-03-06 13:51:59 by Castore
0Helpful
2536Views
15Replies
I am a user of MR600 V1 in Taiwan. My MR600 V1 router has been unable to continuously enable 4G+ carrier aggregation. It only appears when downloading files and testing speed. Which ISP profile and fi
Firmware UpdateBand SelectionCarrier Aggregation
By yanru · Latest post 2025-02-24 08:59:37 by yanru
2Helpful
263Views
3Replies
Problem: 1. Does not get IP and DNS for IPv4. No internet. 2. Get IP and DNS for IPv6 but get internet connection randomly. 3. Band change option is not found. Band changes randomly. 4. Upgraded the f
Network ConnectivityBand SelectionIPv4 Problem
By adnan_bafa · Latest post 2025-02-24 07:31:14 by Marvin_S
0Helpful
147Views
1Replies
Then theres few problems that risen after using for little time that i hope fixes with future fw updates: 1. Cannot force "only 5g" When you put the modem in onky 5g it just "disconnect" and not even
Band SelectionInstallationTP-Link ID RelatedFirmware UpdatePlease
By Finnish · Latest post 2025-02-19 08:08:02 by Luigireport
13Helpful
4175Views
9Replies
Hi, It's me again, had to return my x50-5G, got this Archer nx200 instead, problems again with slow speed. already changed 3 sim cards, this time tested sim card before inserting inside router, speed
Firmware UpdateNetwork ConnectivityBand SelectionMobile Wi-Fi
By justgytis · Latest post 2025-02-05 08:35:55 by Marvin_S
0Helpful
852Views
3Replies
123...
123...