Wi-Fi Routers Forums - Home Network Community

TP-Link Archer C6 routers frequently freeze or stop responding

I am writing to request technical assistance regarding a serious issue with multiple TP-Link Archer C6 routers deployed in our company network. We are currently using 22 TP-Link Archer C6 routers acro

Link AggregationArcher C6

By Kashif-Nazir · Latest post a week ago by Joseph-TP

0Helpful

143Views

1Replies

TP-Link Archer AX55 not working with Alcatel-Lucent I-240G-B ONT at 1000 Mbps

Hello, I recently bought a TP-Link Archer AX55 router, but I’m facing an issue with my Alcatel-Lucent I-240G-B ONT connection. When the Internet port negotiation speed is set to 1000 Mbps, the router

Network ConnectivityFirmware UpdateMulti-GigabitLink AggregationONT Compatibility

By ahmedengu · Latest post 2025-11-09 23:05:51 by woozle

0Helpful

199Views

5Replies

be550 cannot use link aggregation

I bought a be550 for my nas, because the tplink homepage in HongKong show that can use link aggregation. But after i got it, i find everywhere in the setting interface, no link aggregation. I google a

Link AggregationBE550Firmware Update

By asalok · Latest post 2025-08-22 03:48:58 by Kevin_Z

3Helpful

2440Views

19Replies

After Upgrading firmware Static aggregation is gone

So I got two new BE3600 units for my home setup and NAS. While setting them up, I managed to access the settings and set up static aggregation. But after updating, that setting was gone, and I was con

Firmware UpdateInstallationLink Aggregation

By Guttyy · Latest post 2025-06-09 09:01:41 by Joseph-TP

0Helpful

717Views

6Replies

BE800 LACP Support in AP mode?

Does the BE800 formally support LACP in Access Point mode? I note there are options in the BE800 WR to configure pairs of LACP ports but not in the BE800 AP. However it seems to work but not consisten

Network ConnectivityAccess Point ModeLink Aggregation

By StFual · Latest post 2025-02-26 17:21:54 by terziyski

2Helpful

1487Views

3Replies

BE550 and LACP in a Mesh

Hello All I am using a mesh of 3 x BE550 routers in my home using Easymesh. I have a synology 918+ NAS connected to one of the satallite BE550s. The Synology NAS has 2x1gb ethernet links and can be co

Network ConnectivityLink Aggregation

By jpmbosco · Latest post 2025-02-25 08:30:17 by Joseph-TP

0Helpful

842Views

1Replies

SolutionGet Synology NAS work well with Archer AX6000 when Link aggregation enabled

Recently, we got a case reported by one end-user that he failed to connect his Synology NAS DS918+ to the Archer AX6000 with Link Aggregation enabled. As per customer said, the network diagram is Mode

OfficialHighlighted ThreadLink Aggregation

By

Solla-topee · Latest post 2025-01-04 19:13:27 by cosplayIT

11Helpful

14022Views

14Replies

LAG + 2nd switch causing network loops

Hello, I have a AX73 router with static LAG configured (2 ports). The switch connected to it, TL-SG108E also has LAG configured on the interface. I connected a 2nd switch to the router (TL-SG605E) and

Network ConnectivityLink Aggregation

By danoffline · Latest post 2024-10-31 07:58:44 by Kevin_Z

0Helpful

1559Views

4Replies

AX73 Agregation (Static LAG)

Hi, I bought a Tenda TEM2010F switch that supports 2.5Gbit/s and supports Static Aggregation. This switch is set to Static LAG and the specific ports are connected to a TP-Link Archer AX73 router wher

Link AggregationFeature Request

By Petr89 · Latest post 2024-10-30 13:22:12 by danoffline

2Helpful

1410Views

3Replies

BE9300 Link Aggregation with IPTV/VLAN enabled

My ISP uses a VLAN ID 2 under Network Settings / IPTV/VLAN / Internet VLAN. I have to therefore enable IPTV/VLAN under Network Settings. if I then try to enable Link Aggregation under Network Settings

Link Aggregation

By Zedoz · Latest post 2024-08-05 09:47:57 by Marvin_S

0Helpful

1738Views

1Replies