Home Network Community > Deco > Can’t connect to DVR remotely through Deco M5
< Deco

Can’t connect to DVR remotely through Deco M5

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Can’t connect to DVR remotely through Deco M5

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Can’t connect to DVR remotely through Deco M5
Can’t connect to DVR remotely through Deco M5
2019-09-15 19:55:41
Model: Deco M5  
Hardware Version:
Firmware Version: 1.3.1

Hi There,

Novice in need of assistance.

 

I have a DVR connected to Deco M5 in router mode. I can view camera footage when connected to wifi of the same network but I cannot view remotely.

 

I followed port forwarding instructions as per the instructions but I am still unable to connect to dvr remotely. I also cannot confirm port forwarding through canyouseeme.

 

Details of my set up are below. Any help with this would be greatly appreciated.

 

  0      
 
  0      
 
#1
Options
3 Reply
Re:Can’t connect to DVR remotely through Deco M5
2019-09-15 23:56:21

On the WAN screen you have:

 

IP address 192.168.2.11

Default Gateway 192.168.2.1

Default DNS 192.168.2.1

 

Subnet Mask 255.255.255.0

 

This means that all devices on your network will have IP addresses in the format 192.168.2.x

 

You are trying to port forward to a 192.168.0.x address which I would not expect to work.  It should be a 192.168.2.x address?

 

Craig

  0  
  0  
#2
Options
Re:Can’t connect to DVR remotely through Deco M5
2019-09-16 00:35:11

@CW185 Hmmmm...deco assigned the IP address 192.168.0.115 to my DVR and all my other devices are in the same format. Is the WAN incorrect? Can that even be changed?

  0  
  0  
#3
Options
Re:Can’t connect to DVR remotely through Deco M5
2019-09-16 02:10:37

@Tshanks78 

 

The current WAN IP is a private IP address, while to make port forwarding work, it should be the public IP address. 

 

There should be another router with public internet IP address existed, you need open the port for the Deco on it so that you can build up a tunnel for the DVR which you can access it remotely.

 

May it help and have a good day. 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 4113

Replies: 3

Related Articles
 How do I connect my CCTV DVR to Deco M5
2575 0
 Can’t connect M5
202 0
 Can’t remotely access Deco M9
445 0
I can’t connect
198 0
 Deco M5 - poor wifi and can’t optimise
283 0
 Connect adapter to DVR
627 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.