Home

Forums

Stories

Knowledge Base

Home Network Community > Deco > Whole network IP address changes after network outage

< Deco

Whole network IP address changes after network outage

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Whole network IP address changes after network outage

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Feng-L

2019-11-21 07:18:12

Posts: 3

Helpful: 6

Solutions: 0

Stories: 0

Registered: 2019-11-21

Whole network IP address changes after network outage

2019-11-21 07:18:12

Model: Deco M9 Plus

Hardware Version: V1

Firmware Version: 1.3.0 Build 20190821 Rel. 54024

There is a maintainence by ISP, and after the internet recovery, my LAN IP segment changes. All IP no longer starts with 192.168.68.x, but it changes to 192.168.0.x. For example, now my main Deco uses 192.168.0.1. All the address reservation and port forwarding IP address changes as well, so no issue with that part.

Is this IP changing behavior working as intended, or caused by some other issue?

Thanks in advance.

3 Reply

Mitya

LV4

2019-11-21 07:22:35

Posts: 310

Helpful: 73

Solutions: 9

Stories: 0

Registered: 2018-08-09

Re:Whole network IP address changes after network outage

2019-11-21 07:22:35

@Feng-L

Check your WAN-connection, if it is 192.168.68.0/24. Deco can change LAN network, if WAN is the same. Otherwise it should not change anything automatically.

Feng-L

LV1

2019-11-21 07:48:54

Posts: 3

Helpful: 6

Solutions: 0

Stories: 0

Registered: 2019-11-21

Re:Whole network IP address changes after network outage

2019-11-21 07:48:54

@Mitya

No, the WAN IP is assigned by ISP with a public one different from 192.168.x.x.

Kevin_Z

2019-11-28 01:22:25

Posts: 21776

Helpful: 5146

Solutions: 2575

Stories: 21

Registered: 2018-12-24

Re:Whole network IP address changes after network outage

2019-11-28 01:22:25

@Feng-L

Except the WAN IP of Deco, please check the WAN DNS to verify whether it is in the same segment of the LAN IP (192.168.68.x); If they are in the same network, to avoid IP conflict, the Deco will change its LAN IP to another one.

You can try to change the WAN DNS to 8.8.8.8/8.8.4.4 and then change the LAN IP of Deco to 192.168.68.x .

https://www.tp-link.com/support/faq/1855/

May it help.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

Whole network IP address changes after network outage

Whole network IP address changes after network outage

Information

Voters 0

Tags