Home Network Community > 5G/4G Wi-Fi Routers/MiFi > ****Archer MR600 - 2CA bands Aggregation - New Bands***
< 5G/4G Wi-Fi Routers/MiFi

****Archer MR600 - 2CA bands Aggregation - New Bands***

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
123456

****Archer MR600 - 2CA bands Aggregation - New Bands***

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
60 Reply
Re:****Archer MR600 - 2CA bands Aggregation - New Bands***
2020-09-20 07:27:45

Hi @Abhi093


Can you suggest me some antennas? I live in a suburban area and have Multiple Jio/Airtel Towers within 2kms of my home. I tried to figure this out and have looked at LDPA and patch antennas. Some people in one of the threads also suggested getting a omnidirectional antenna but I am not sure which omnidirectional antenna I should get.

 

Indoors, I am only getting 1-2 bars, 50% signal strength, < 10 db SNR, -80+DB RSSP and -10 - -20DB RSSQ.

 

Indoors, On Jio with the router in 3+5 configuration I am getting 10-15mbps speed

On Airtel, In 3+40 configuration I am getting 20mbps speed. Upstairs, On airtel, I was getting 50-60mbit speed.

 

So, I think getting an antenna will definitely help.

 

So, Please suggest what antenna and wires I should get? (Distance will be around 15m)

 

Thank you so much for your comments on this forum. They have been immensely helpful in figuring out some of this stuff.

  1  
  1  
#32
Options
Re:****Archer MR600 - 2CA bands Aggregation - New Bands***
2020-09-20 07:31:12
Hi @ishanjain28, Thank you for highlighting this fact. I have already spoken with Amazon CS, they are ready for the replacement. But no return for this product. On the product page it self they have provided the TP Link number and are suggesting to call them and ask for solution. Also had word with my friends and here, even the replacement units not providing the solution unless we have a new version like V2 which might be latest one. Even today had asked in Amazon product page that if V2 is available. So no point of getting it replaced cause all the units are same. Thank you and regards,
Thank you and regards, Debatosh Kamila Email: debatoshkamila@gmail.com
  0  
  0  
#33
Options
Re:****Archer MR600 - 2CA bands Aggregation - New Bands***
2020-09-20 07:31:44

@ishanjain28  pleas check your message.

Regards, Abhi
  0  
  0  
#34
Options
Re:****Archer MR600 - 2CA bands Aggregation - New Bands***
2020-09-20 07:47:19

Hi @ishanjain28,

 

Yes, i think you are right. Might be some help we can get by using the Antenna till the time the lastest firmwares comes and our problem goes off.

 

@Abhi093 

 

Could you please suggest some of the options for the Antenna? I would be travelling to my native place (Odisha) in coming days and would be requiring good interent speed for WFH case,it would be a great help. Airtel and Jio towers are avilable within 1kM to 2KM range.

Aslo if any one else can sugget, it would be much appriciated.

Thank you and regards, Debatosh Kamila Email: debatoshkamila@gmail.com
  0  
  0  
#35
Options
Re:****Archer MR600 - 2CA bands Aggregation - New Bands***
2020-09-20 07:50:45

@Debatosh  hi Debatosh.

 

Check your message box in your TP link community account.

Regards, Abhi
  0  
  0  
#36
Options
Re:****Archer MR600 - 2CA bands Aggregation - New Bands***
2020-09-20 08:27:19

@Debatosh I agree that I have a buggy firmware at UE side. However, during the last week my closest Airtel tower has been upgraded to 4 TDD sector antennas.( Earlier it had 3 TDD sectors) Post that I am not getting TDD Band 40 (2300 MHz). Earlier I used to get all 2CA combinations with Airtel with constant speeds upto 90 Mbps. Now the Airtel infratel team had changed the antenna orientation and I am only getting FDD band 3 (1800 Mhz). Really sad. Though I have Jio as an alternative so it's ok. But after complaining about this to local BSS Engineer they have agreed to fix the Antenna orientation for TDD 2300 MHz Sector , but they don't have a timeline. The tower is just 120 meters from my location

 

Awaiting with patience.

 

Regards, Abhi
  1  
  1  
#37
Options
Re:****Archer MR600 - 2CA bands Aggregation - New Bands***
2020-09-22 16:45:47

@Abhi093 

Thank you. Let's hope for the best.

Thank you and regards, Debatosh Kamila Email: debatoshkamila@gmail.com
  0  
  0  
#38
Options
Re:****Archer MR600 - 2CA bands Aggregation - New Bands***
2020-09-25 05:32:53

@Sunshine @Solla-topee ... Would you guys please check with your developers that,

Abhi093 wrote

@Sunshine @Kevin_Z  Hello Support,

 

I would ask you to please provide newer 2CA band support for the MR600.

 

2CA_1A-40A , 2CA_3A-41A .

 

Most importantly 2CA_40A-40A  is needed at the earliest.

 

Regards,

~Abhi smiley

where do we stand on the 40A+40A band aggregation support in MR600.?

Regards, Abhi
  0  
  0  
#39
Options
Re:****Archer MR600 - 2CA bands Aggregation - New Bands***
2020-09-25 13:43:32

@Abhi093 

 

Hello Abhi,

 

Please suggest me also some antena, I have Jio tower within 1 Km, but signal strengh is not so good. with 3+5 combination i get 25% signal strength.

  0  
  0  
#40
Options
Re:****Archer MR600 - 2CA bands Aggregation - New Bands***
2020-09-25 13:46:53

@Sunshine 

 

Hello,

 

Do you have any update on 40A+40A CA? We all are waiting for such a long time. I had a impression that TPLink listen to its customers.

 

  0  
  0  
#41
Options
123456
Related Articles
Archer MR600 4G BANDS
28892 6
Archer MR600 - 4G Bands selection
25619 11
Archer MR600 V2 Carrier Aggregation & Band Selection
25237 15
MR600 carrier aggregation not working
1606 0
TP Link Archer MR600 does not support carrier Aggregation in India.
2340 3
 Archer MR600(EU) V1 and 4G+ band aggregation
646 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.