Home Network Community > Wi-Fi Routers > Access point mode in Archer C50, AC1200, V2 (2 antennas)
< Wi-Fi Routers

Access point mode in Archer C50, AC1200, V2 (2 antennas)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Access point mode in Archer C50, AC1200, V2 (2 antennas)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Access point mode in Archer C50, AC1200, V2 (2 antennas)
Access point mode in Archer C50, AC1200, V2 (2 antennas)
2020-10-27 23:56:35 - last edited 2020-10-28 08:16:31
Model: Archer C50  
Hardware Version: V2
Firmware Version:

Good day,
 

 

Is there a way to set this router to "access point" mode? I checked all the settings - I do not see one that says "operation mode".

 

I tried disabling the DHCP, but the ipconfig command shows the assigned IP address as 192.168.0.xxx (i.e. assigned by the Archer C50) rather than 192.168.1.xxx (from the address pool coming from the ISP's modem/router).


 

The help will be greatly appreciated.

 

 

Thank you!

  1      
 
  1      
 
#1
Options
1 Accepted Solution
Re:Access point mode in Archer C50, AC1200, V2 (2 antennas)-Solution
2020-10-28 08:16:27 - last edited 2020-10-28 08:16:31

@HowardBannister 

 

Hello, thanks for asking.

 

There is no Access Point mode on the Archer C50 V2, while you can configure it into an access point manually as below:

https://www.tp-link.com/support/faq/1199/

 

Hope this helps.

EasyMesh and TP-Link | Learn what EasyMesh is and how it works on TP-Link Routers and Range Extenders.
Recommended Solution
  1  
  1  
#2
Options
3 Reply
Re:Access point mode in Archer C50, AC1200, V2 (2 antennas)-Solution
2020-10-28 08:16:27 - last edited 2020-10-28 08:16:31

@HowardBannister 

 

Hello, thanks for asking.

 

There is no Access Point mode on the Archer C50 V2, while you can configure it into an access point manually as below:

https://www.tp-link.com/support/faq/1199/

 

Hope this helps.

EasyMesh and TP-Link | Learn what EasyMesh is and how it works on TP-Link Routers and Range Extenders.
Recommended Solution
  1  
  1  
#2
Options
Re:Access point mode in Archer C50, AC1200, V2 (2 antennas)
2020-10-28 16:53:29

@Kevin_Z - thank you, that worked! 

 

Greatly appreciated!

  0  
  0  
#3
Options
Re:Access point mode in Archer C50, AC1200, V2 (2 antennas)
2020-10-29 02:32:51

@HowardBannister 

 

Hi, glad to hear that it works, congrats.^_^

 

If need any further help, just let us know.

 

Good day~

EasyMesh and TP-Link | Learn what EasyMesh is and how it works on TP-Link Routers and Range Extenders.
  0  
  0  
#4
Options

Information

Helpful: 1

Views: 3282

Replies: 3

About Us
Press
Copyright © TP-Link Corporation Limited. All rights reserved.