Home Network Community > Wi-Fi Routers > Can't Access the Router Remotely
< Wi-Fi Routers

Can't Access the Router Remotely

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

Can't Access the Router Remotely

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Can't Access the Router Remotely
Can't Access the Router Remotely
2020-11-18 07:49:30 - last edited 2020-11-22 18:54:33
Model: TL-WR940N  
Hardware Version:
Firmware Version: V6

Hi, 

 

I'm trying to access my router over the Internet, I set up a noip account and logged in through the router but still I'm unable to reach the router. Any suggestions or troubleshooting I can do. 

 

Thanks

  0      
 
  0      
 
#1
Options
15 Reply
Re:Can't Access the Router Remotely
2020-11-19 00:41:48

@julamee 

 

If you have any intermediate devices before the router (modem, firewall, etc.) they should have the remote port opened as well to be able to connect.

The remote management configuration on your router should look similar:

That's in case all remote devices are allowed to connect to your router.

If you want only a particular device to connect remotely then type its real IP address instead.

Also the port you are using should not duplicate with any other public service in your network (i.e if you have a public WEB server then you should choose a different than port 80).

 

The Dynamic DNS configuration:

 

Successful registration of your no-ip.com account is when you see "Success!" in the Connection Status field.

Don't forget to check Enable DDNS checkbox.

 

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
  3  
  3  
#2
Options
Re:Can't Access the Router Remotely
2020-11-22 06:46:42

@Ivaylo 

 

Thank you for your reply.

 

I do not have any intermediate device, only the router.

 

Remoter management and DDNS configurations.

 

But still cannot access the router over the Internet.

  0  
  0  
#3
Options
Re:Can't Access the Router Remotely
2020-11-22 16:35:34
Try to change the port, for example 8080 and see if that helps.
If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
  0  
  0  
#4
Options
Re:Can't Access the Router Remotely
2020-11-22 16:40:19

@Ivaylo 

I did that already, I tried 8080 and several others but none worked for me. 

  0  
  0  
#5
Options
Re:Can't Access the Router Remotely
2020-11-22 17:56:14

@julamee 

 

Are you sure your ISP is assigning a public IP address to your router?

 

In case you are not sure, go to a website like "www.ipchicken.com" or similar and then compare the IP address it shows you to the IP address your TL-WR940N shows under "Network" -> "WAN".

  0  
  0  
#6
Options
Re:Can't Access the Router Remotely
2020-11-22 17:59:03
So your connection is ethernet cable from your ISP, which goes directly into your router ?
If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
  0  
  0  
#7
Options
Re:Can't Access the Router Remotely
2020-11-22 18:19:35

@woozle 

Thank you for your reply. 

 

They're different. What difference does that make? 

  0  
  0  
#8
Options
Re:Can't Access the Router Remotely
2020-11-22 18:20:34

@Ivaylo 

Am ethernet cable from a nanostation m5 to my router. 

  0  
  0  
#9
Options
Re:Can't Access the Router Remotely
2020-11-22 18:37:05
Under "Network" -> "WAN" does your IP address look like "192.168....."
If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
  0  
  0  
#10
Options
Re:Can't Access the Router Remotely
2020-11-22 18:41:33 - last edited 2020-11-22 18:42:17

@julamee 

 

If the two IP addresses are different, then it means the WAN IP address of your router is probably not a public IP address and thus can't be reached from the internet.

 

Is the Nanostation set up in router mode or bridge mode?

If it's in router mode, can you find out if the Nanostation has a public IP address assigned to it?

 

 

  3  
  3  
#11
Options
12

Information

Helpful: 0

Views: 2782

Replies: 15

Related Articles
 Can't access router remotely
629 0
 Can't access remotely my router...
602 0
 Unable to access router remotely
680 1
I can't access a tplink router wr840N which is behind WR940N
1850 0
 I can not remotely access my Router
711 0
Can't access to the router
166 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.