Home Network Community > Wi-Fi Routers > Archer C6 V2.0 latest firmware WAN ports
< Wi-Fi Routers

Archer C6 V2.0 latest firmware WAN ports

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer C6 V2.0 latest firmware WAN ports

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer C6 V2.0 latest firmware WAN ports
Archer C6 V2.0 latest firmware WAN ports
2022-09-24 15:16:22 - last edited 2022-09-24 16:36:14
Model: Archer C6  
Hardware Version: V2
Firmware Version: 1.3.7 Build 20220613 rel.64828

Hi,

 

nmap finds these ports open when I scan the WAN ipaddress

 

port 22 from the WAN port? dropbaer daemon

Also an upnp om port 1900 seems to be open.

 

 

I can not find where to close these ports.

Can it be done?

 

regards Henk

 

 

  0      
 
  0      
 
#1
Options
2 Accepted Solutions
Re:Archer C6 V2.0 latest firmware WAN ports-Solution
2022-09-24 16:32:08 - last edited 2022-09-24 16:36:14

GRL wrote

  @hellsblade 

 

Set up a virtual server (port forwarding) forwarding them no a non existing IP address off your subnet.  IE, if you subnet is 192.168.1.x forward the ports to 10.0.0.1

 

this will close them

  @GRL  Great tip. I never would have tought of that. 

Thanks Henk

Recommended Solution
  0  
  0  
#3
Options
Re:Archer C6 V2.0 latest firmware WAN ports-Solution
2022-09-24 16:39:29 - last edited 2022-09-24 16:39:47
Oops. cannot use another non existing lan so i used a non existing ip outside my dhcp range. That did the job as well
Recommended Solution
  0  
  0  
#4
Options
3 Reply
Re:Archer C6 V2.0 latest firmware WAN ports
2022-09-24 15:45:41

  @hellsblade 

 

Set up a virtual server (port forwarding) forwarding them no a non existing IP address off your subnet.  IE, if you subnet is 192.168.1.x forward the ports to 10.0.0.1

 

this will close them

Owner of: ER605 v1, ER605 v2, ER7206 v1, SG1024DE v4.2 and AX53 v1
  0  
  0  
#2
Options
Re:Archer C6 V2.0 latest firmware WAN ports-Solution
2022-09-24 16:32:08 - last edited 2022-09-24 16:36:14

GRL wrote

  @hellsblade 

 

Set up a virtual server (port forwarding) forwarding them no a non existing IP address off your subnet.  IE, if you subnet is 192.168.1.x forward the ports to 10.0.0.1

 

this will close them

  @GRL  Great tip. I never would have tought of that. 

Thanks Henk

Recommended Solution
  0  
  0  
#3
Options
Re:Archer C6 V2.0 latest firmware WAN ports-Solution
2022-09-24 16:39:29 - last edited 2022-09-24 16:39:47
Oops. cannot use another non existing lan so i used a non existing ip outside my dhcp range. That did the job as well
Recommended Solution
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 320

Replies: 3

About Us
Press
Copyright © TP-Link Corporation Limited. All rights reserved.