Issue with AddiHardwareVer when installing OpenWRT 22 Snapshot on EAP225 Outdoor V3
Hi,
I am trying to build & install OpenWRT 22 Snapshot on EAP225 Outdoor V3.
I was able to build & install it in some previous EAP225 Outdoor V3 but later brought units i was not able to install.
Steps to Reproduce:
1. CMD: cliclientd stopcs
Given through ssh cli.
And AP responded with Success
2. In TPLink Webbrowser Page, in System Tab, Firmware upgrade tab. Tried to upload/flash build openWRT image.
Below are the logs taken through UART.
NM_Debug](nm_region_getRegionName) 00192: Flash region info, code: 841, name: US.
[ 167.130000] query url: tplinkeapnet
[ 167.140000] query url: tplinkeapnet
[utilities_debug: postFirmwareRpm:179]post request
memFree = 64958464
[utilities_debug: getFirmwareRpm:145]get request
[NM_Debug](nm_fwup_buildUpgradeStruct) 02194: nFileBytes = 8321425
[NM_Debug](nm_lib_getProductInfoFromNvram) 00928: productinfo from NVRAM is (EAP225-Outdoor(TP-Link|UN|AC1200-D):3.0
key=BgIAAAAkAABSU0ExAAQAAAEAAQDZtUNzD6KsxO4Tfx/Sp8S7w8TwPWwoppXy77wSPNs5WoV+Wr4kh09nu70vHVmSPji5KFUG+hmRjapsJsIJj+M0Zmd4EycKY8r0Ea3D4XO/uvloX4VHVPsDZkm8Krian5iNy6BgApVlebx0zQxto0GkgvPBq1nhoZxJNapLghGO7w==
rsaKey=BgIAAACkAABSU0ExAAQAAAEAAQDZaGCNzHjzrgNoCjyHKa0TIkgmqE5kheNhZHs23TmAbHXN0dFwdNOqqDOTmTdoN1+zW6KY3YkkwNypoZbDTR3sKdSdIDTNnftfHhRAlR9l4lNnnvfbUWRDqaGD2nAkdasXXfD5c23COMvAEjLJXzwqZjNmj27ZgrrTlH9SoDPe=
HWID=96455746BD4C5113D5E35DAF2CC3CA9B
)
[NM_Debug](nm_region_getRegionName) 00192: Flash region info, code: 841, name: US.
[NM_Debug](checkSupportList) 01099: Check support-list:SupportList:
[NM_Debug](checkSupportList) 01099: Check support-list:EAP225(TP-Link|UN|AC1350-D):3.0
[NM_Debug](checkSupportList) 01099: Check support-list:EAP225(TP-Link|UN|AC1350-D):3.20
[NM_Debug](checkSupportList) 01099: Check support-list:EAP225(TP-Link|UN|AC1350-D):4.0
[NM_Debug](_checkSpecSuppList) 01031: check spec region support-list: EAP225(TP-Link|CA|AC1350-D):4.0
[NM_Debug](checkSupportList) 01099: Check support-list:EAP225-Outdoor(TP-Link|UN|AC1200-D):1.0
[NM_Debug](checkSupportList) 01099: Check support-list:EAP225-Outdoor(TP-Link|UN|AC1200-D):3.0
[NM_Debug](checkSupportList) 01102: Firmwave supports EAP225-Outdoor(TP-Link|UN|AC1200-D):3.0, check OK..
[NM_Debug](nm_fwup_verifyFwupFile) 02429: curSoftVer:5.1.0 Build 20220926 Rel. 62456,newSoftVer:0.0.0 Build 20230704 Rel. 23498
AddiHardwareVer check: NEW(0x1) >= CUR(0x2), Failed, Refuse upgrade!
[Error][checkFirmware] 278: nm_api_verifyFwupFile failed, errCode 50008
[NM_Debug](nm_region_getRegionName) 00192: Flash region info, code: 841, name: US.
It is highly appreciated if anyone could help on this.
Thanks in Advance.
Regards,
Srisurya.