Hi  @Clive_A 

 

Thanks for replying. Onto your comments: 

 

1.: Yeah, I'm aware. From what I see, the SFP+ module has negotiated at 10gb on one side and 2.5Gbs on the other so it seems to be working as expected. I know this because when I change the ISP Router to Gateway mode, I can see it's negotiated 2500 on its side. 

 

2.: I've got only one module, it's currently in Port-1. It's not a heavy load really, but I'm monitoring the temps. CPU is at 57, PCB at 54. Typical temperature in the module when checked at DDM is 65-70 and I've never seen it past 70. 

 

Surprisingly now, sometime the whole thing works as expected. I was running some tests yesterday, and after plugging and un-plugging between WAN Ports 1 and 4, I managed to get it to output the full speed. However, if for whatever reason I need to reboot the ISP Router (which is annoyingly frequently) it's back to reduced speeds for a while. 

 

Thanks,

 

T

 

 Hi  @Clive_A,

 

Thank you. Yes, I can confirm that at least for now, this is working - I'm just not sure what's going to happen when I need to reboot the ISP modem. 

 

In cany case, do we have any troubleshooting tools we could use? I checked the logs, couldn't really see anything especificaly. For now, Flow Control is also on on the WAN port so I'm not going to change it but I know there's been some discussion around it in the past. 

 

Best,

 

T

Well, spoke too soon. I had to reboot my ISP modem today (having some other issues with Rogers. Lo and behold, I'm back to slow speeds again. This makes no sense to be honest :/

 

Edit:

 

I've found something interesting. When I plug the network cable in the SFP+ port with the transceiver, my CPU skyrockets. When I switch it back to Port-4, it goes down again. But regardless of going down, speed will still be capped at 280 - 300. 

 

 

I'm having an equal issue.

 

I have a 10G internet connection. Router shows 10G connection. But the fastest I get is ~400MBs.

 

Connect direct, I can get speed tests of ~5000 to 7000 depending on speed test site.

 

I ordered a 2nd ER8411 router to test. I'll test it this week.  Also got 4 SPF+ 10G modules to test too.  (I'll keep it as a spare)

 

Hi  @Clive_A 

 

I monitored more closely, and it's a temporary spike whenever I change either to SFP+ port 1 or Wan Port 4. It drops quickly and the speed remains low so not sure if it's actually related. 

 

ISP modem on the other side is in Bridge mode so I can't access it to confirm the link speed there. However, when connected to the gigabit wan port it gives me amber led while when connected to the module it gives green led. This is consistent with the tests I've performed when I had it in Gateway mode temporarily running the tests. 

 

Speeds on Wan 1gbs Port 4 are normal. All I'm doing is switching Wan connection from SFP to Port 4 giga and everything works at giga speeds. I've tested the module and I know it can negotiate 2.5 so the only variable is the actual SFP+ slot that's working weirdly. 

Please keep us posted if you find anything! I'm trying to troubleshoot some more.

Folks,

 

I may be on to something. I managed to get full speeds when using SFP+ port. Following these exact steps: 

 

1) Turn off Router and ISP Modem 

2) Turn on Router - wait for it to come up completely (on the XB7, it's a solid white line). 

3) Connect the cable from the router 2.5 port to SFP+ port with the ER8411 still off. 

4) Turn on the ER8411. 

 

And voila, I got full speeds. 

 

My two cents is that something in the auto-negotiation and/or flow control breaks if the link goes down. 

 

Is there any way we can ssh into the router and check what's the wan port status there? It *may* be that the interface is showing Flow Control is on, but it's actually not on.