TP-Link XC220-G3v v2.30 updated firmware required for BSNL INTERNET ISSUE
Hello, I have Bsnl FTTH Connection. Recently bought TP-LINK XC220-G3V.
I attempted to set up Internet, but it was not able to connect. The user name, password, and VLAN ID are correct (provided by BSNL), but it still appears to connect and disconnect, But VOIP is configured and status connected. But the Internet is not working..
How can get updated firmware? official support page downloads not available.
Hardware Version:XC220-G3v v2. 30 00000000
firmware Version : Datecode2301051715
Kindly help as soon as possible.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@sasebruh i have downloaded the brazil version, as suggested some where in this post, but still i have failed to activate voice , however my internet connection is working well. it will be great help, if you can forward me the firmware link to try once again (confeder8.international@gmail.com) thanks in advance.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Hi All,
There is no issue with the firmware. I have completed the configuration and made a post about it. Please visit the post using the URL below:
techwave|j2dk|in use dote insterd of | to form the url
It is not allowing me to put the link or snap here
Thanks.
DP
- Copy Link
- Report Inappropriate Content
@Pradeep_R can u plz share the configuration details, my local isp provider is supporting, they suggesting me to buy new router, if u share the configuration it will be usef
- Copy Link
- Report Inappropriate Content
@mahat
To all who are having configuration issues.
Internet configuration (PPPoE GPON/EPON):
Type: PPPoE
VLAN: Ask LCO or contractor.
Multucast VLAN: Usually disabled but ask to confirm.
Username
Password: *****
MTU: 1460 (best), 1480 (default), 1492 (max)
For finding the optimal MTU checkout Ping Test to determine Optimal MTU Size on Router from NetGear.
NAT, IGMP Proxy enabled.
DNS set: 1.1.1.1; 8.8.8.8; or vice versa
IPv6: Enable only if you get some gateway IP in Internet IPv6 section in the Status page (indicates IPv6 available at BNG).
DNS IPv6 set: 2001:4860:4860::8888; 2606:4700:4700::1111; or vice versa
Telephone Interface (IPoE GPON/EPON):
Type: Dynamic IP
VLAN: Generally 1849 or 1831 / 1830 but ask to confirm.
MTU: 1500 (default, do not change)
NAT, IGMP Proxy enabled.
IPv6: Enable only if you get some gateway IP in Internet IPv6 section in the Status page (indicates IPv6 available at BNG).
Interface Binding: VoIP
Telephony Setup:
Provider: Other
Phone number: +91[std-code][8-digit-landline-no]
Registrar Address: Ask for the address.
Authentication ID: +91[std-code][8-digit-landline-no]
Password: Ask.
SIP Proxy: Ask for the address (same as registrar address).
Outbound Proxy: Ask for the IP or the address.
Other setting (iykyk):
QOS: enabled
DOS Protection enabled & set to high.
Reboot Schdule: Everyday 3am to 6am.
LAN DNS (set manually if you wish).
- Copy Link
- Report Inappropriate Content
@Udhaya Hi , Could you provide the latest firmware link.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 10481
Replies: 42
Voters 0
No one has voted for it yet.