Home Network Community > Powerline Adapters > TL-WPA4220 KIT wifi password change
< Powerline Adapters

TL-WPA4220 KIT wifi password change

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TL-WPA4220 KIT wifi password change

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TL-WPA4220 KIT wifi password change
TL-WPA4220 KIT wifi password change
2023-11-16 23:33:58 - last edited 2023-11-23 08:53:50
Model: TL-WPA4220 KIT  
Hardware Version:
Firmware Version:

Hi

Is there another method (other than Tether app) to change the wifi setting  (wifi password)?

I tried the tether app but it did not work.

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:TL-WPA4220 KIT wifi password change-Solution
2023-11-21 14:38:20 - last edited 2023-11-23 08:53:50

  @Sunshine 

Hi

Sorry for the delay in replying.

Thank you TO everyone who helped me.

I managed to change the wifi settings by using another method (Dos) via my laptop:

first i unplugged the master powerline

plugged the slave powerline and connected it to the laptop via ethernet cable

i went to Command prompt and typed CD\ pressed enter

then ip config and pressed enter

i got  the default geteway ip  ( 192.168.0.1 or whatever it gives you)

i launched chrome browser and used the gateway ip to login 

   the ipv4 address can be used instead   if the gateway ip does not work 

that is how i managed to access to the powerline settings

 

 

Recommended Solution
  0  
  0  
#5
Options
5 Reply
Re:TL-WPA4220 KIT wifi password change
2023-11-17 03:07:37

  @fishass 

 

Why don't you try via web browser ? Go to http://tplinkplc.net or http://tplinkplclogin.net/ then change the password here:

N.B. (you need to be connected wirelesly to the powerline extender to access its web management page)

 

 

or you can use the tpPLC utility to do the same - here's a guide.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  1  
  1  
#2
Options
Re:TL-WPA4220 KIT wifi password change
2023-11-17 06:12:52

terziyski wrote

  @fishass 

 

Why don't you try via web browser ? Go to http://tplinkplc.net or http://tplinkplclogin.net/ then change the password here:

N.B. (you need to be connected wirelesly to the powerline extender to access its web management page)

 

 

or you can use the tpPLC utility to do the same - here's a guide.

Hi

Thanks for your help

it does not give me this page but it tells me that there is an issue even though i am connected wirelessly to the the tp powerline.

I also tried the tpPLC utility .

Thanks

  0  
  0  
#3
Options
Re:TL-WPA4220 KIT wifi password change
2023-11-17 08:49:21

  @fishass 

 

Hi，thanks a lot for terziyski's help, normally the provided two methods should both work.

May I know the hardware version of your TL-WPA4220? and it is working fine now, right?

 

When you try the tpPLC utility, can your powerline extender be detected by the utility? please share with us the screenshot to show the problem.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#4
Options
Re:TL-WPA4220 KIT wifi password change-Solution
2023-11-21 14:38:20 - last edited 2023-11-23 08:53:50

  @Sunshine 

Hi

Sorry for the delay in replying.

Thank you TO everyone who helped me.

I managed to change the wifi settings by using another method (Dos) via my laptop:

first i unplugged the master powerline

plugged the slave powerline and connected it to the laptop via ethernet cable

i went to Command prompt and typed CD\ pressed enter

then ip config and pressed enter

i got  the default geteway ip  ( 192.168.0.1 or whatever it gives you)

i launched chrome browser and used the gateway ip to login 

   the ipv4 address can be used instead   if the gateway ip does not work 

that is how i managed to access to the powerline settings

 

 

Recommended Solution
  0  
  0  
#5
Options
Re:TL-WPA4220 KIT wifi password change
2023-11-23 08:54:20

  @fishass 

 

Thanks a lot for the update, glad to hear that you've managed to customize the wireless settings.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 912

Replies: 5

Related Articles
TL-WPA4220 KIT)wireless keeps turning off
657 0
 TL-WPA4220 KIT - wifi cloning
775 0
which differences between TL-WPA4221 KIT and TL-WPA4220 KIT
5286 0
 How to change the user name and password for TL-WPA4220 KIT?
446 0
 wifi name and password change in TL-WPA 4220 kit V1
5754 0
TL-WPA4220 wifi stability issues
2461 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.