Business Community > WiFi > EAP660HD disconnected, blinking LED
< WiFi

EAP660HD disconnected, blinking LED

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

EAP660HD disconnected, blinking LED

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
EAP660HD disconnected, blinking LED
EAP660HD disconnected, blinking LED
2024-02-23 00:15:43
Tags: #Network Connectivity
Model: EAP660 HD  
Hardware Version: V1
Firmware Version: 1.2.7

Greetings!

 

My POE+ powered EAP660HD disconnected at random today.  Upon investigation the AP had a blinking LED.  I physically disconnected the AP for about 20 minutes, and reconnected it in an attempt to restart it fresh.  When reconnected, the AP's LED continuously blinks.  It is not responding to ping on its IP or fallback IP address.  The POE switch indicates the AP is taking power, but is not connecting (no connection LED).  I have since tried multiple cold reboots, and resetting with the RESET button.  I have not found a solution and the AP remains in its locked blinking state.

 

Has anyone experienced this, or can offer a solution? 

  0      
 
  0      
 
#1
Options
6 Reply
Re:EAP660HD disconnected, blinking LED
2024-02-23 02:05:29

Hi @900mhz ,

 

Based on our experience, this issue is usually caused by the physical connection, please change the Ethernet cable and check the power supply.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#2
Options
Re:EAP660HD disconnected, blinking LED
2024-02-23 13:51:27

  @Hank21 I tried swapping cables, ports, and tried it without POE+ (hard wiring into the wall wart).  None of these work.

  0  
  0  
#3
Options
Re:EAP660HD disconnected, blinking LED
2024-02-26 01:47:08

Hi @900mhz，

 

Please confirm whether the random disconnected EAP is wired or wireless, and make sure your EAP has the latest firmware version EAP660 HD_V1_1.2.10 Build 20231214.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#4
Options
Re:EAP660HD disconnected, blinking LED
2024-02-27 19:18:57

  @Hank21 It is wired into an ER7212PC.  The EAP was on the latest firmware available in Canada (1.2.7)

  0  
  0  
#5
Options
Re:EAP660HD disconnected, blinking LED
2024-02-28 03:22:11

Hi @900mhz,

 

Please confirm whether the firewall and anti-virus software don't block any ports between the EAP and the controller, you may turn off the firewall for testing.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#6
Options
Re:EAP660HD disconnected, blinking LED
2024-02-28 19:00:07

  @Hank21 There are no blockages (EAP connected directly to ER7212 which is also the controller)

  0  
  0  
#7
Options

Information

Helpful: 0

Views: 694

Replies: 6

Tags

Network Connectivity
Related Articles
EAP660HD v1.2.9?
710 0
EAP660HD doesn't startup
1152 0
Set-up Mesh Wifi with EAP660HD with RE
271 0
 new EAP660HD
896 0
EAP660HD HW version 1.0 vs. 1.60
707 0
 Mesh with EAP660HD and EAP245
789 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.