Router IP address 172.16.10.1
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Just unpacked the Archer AX55 to replace the Archer C7. I want to use the same IP for the router 172.16.10.1 and the IP address pool 172.16.10.2 - xxxxxxx.
When I go to Network > LAN and enter the IP 172.16.10.1 for the router, he restarts, and I can't connect to the router, I have reset him.
What has to be done that it works with the new addresses?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@terziyski that's the reason why i started the 1st post :-)
When I change the IP to 172.16.10.1, I click on save, the router restarts and I can't reach the router. Not by the old address (192.168.0.1), nor by the new one. I purged the DNS resolver cache, release the IP and renewed the IP at the laptop.
- Copy Link
- Report Inappropriate Content
This should be straight forward operation as long as the IP address is a private IP address.
I can see that your AX55 FW release is pretty old one. You can update the FW to the latest one and check if there's any difference - here.
What is your router FW region ? This is printed on the device bottom sticker - details.
I would do the procedure like this:
Set AX55 with LAN IP 172.16.10.1/24 - router restarts.
Set a static IP address on the laptop wired network card as 172.16.10.2/24. Connect an ethernet cable between laptop and AX55 LAN port.
Open a browser and point it to the 172.16.10.1 IP address. At this point you should be able to see the AX55 WebGUI.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
A DHCP pool should be in the range of 172.16.10.2 - 172.16.10.254.
Can you post a screenshot of the DHCP settings and error message.
- Copy Link
- Report Inappropriate Content
This is the error message when I try to change the IP address pool first. So this does also not work.
- Copy Link
- Report Inappropriate Content
You have to change the LAN IP address of the router first (router will restart itself) and then set its DHCP server pool.
- Copy Link
- Report Inappropriate Content
@terziyski that's the reason why i started the 1st post :-)
When I change the IP to 172.16.10.1, I click on save, the router restarts and I can't reach the router. Not by the old address (192.168.0.1), nor by the new one. I purged the DNS resolver cache, release the IP and renewed the IP at the laptop.
- Copy Link
- Report Inappropriate Content
This should be straight forward operation as long as the IP address is a private IP address.
I can see that your AX55 FW release is pretty old one. You can update the FW to the latest one and check if there's any difference - here.
What is your router FW region ? This is printed on the device bottom sticker - details.
I would do the procedure like this:
Set AX55 with LAN IP 172.16.10.1/24 - router restarts.
Set a static IP address on the laptop wired network card as 172.16.10.2/24. Connect an ethernet cable between laptop and AX55 LAN port.
Open a browser and point it to the 172.16.10.1 IP address. At this point you should be able to see the AX55 WebGUI.
- Copy Link
- Report Inappropriate Content
I updated the firmware to 1.2.6 Build 20231130
Hardware version: EU v1
then I connected my laptop via Ethernet with the AX55, changed the AX55 IP to 172.16.10.1 and saved (and it restarted automatically)
then I changed the IP of my laptop to 172.16.10.2 and I could connect to the router and change all other settings, like IP address pool.
Changed my laptops IP to DHCP given and the internet works :-)
Thanks a lot @terziyski
At the first trials, I didn't change the IP of the laptop to static, this must have been the problem.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 1234
Replies: 8
Voters 0
No one has voted for it yet.