Omada Software Controller Network topology not showing correctly

Omada Software Controller Network topology not showing correctly

Omada Software Controller Network topology not showing correctly
Omada Software Controller Network topology not showing correctly
2024-08-03 19:58:58 - last edited 2024-08-15 08:28:48
Hardware Version:
Firmware Version: 5.14.26.1

Hi All,

 

I'm running Omada Software Controller as a docker image[1] on a linux host. Recently I have noticed that network topology view is not showing any of my EAP615-wall or EAP655-wall devices and clients connected to them. However I can see my Omada compatiable devices under Devices section as well as all clients under clients section without any issue.

 

 

When inspecting controller logs, I have noticed Stack Overflow Exception in topology calculator occationaly. But there are successful calulation logs printed after those exceptions too.

 

Is there any known bug related to this controller version or this is something specific to my environment?

 

[1] mbentley/docker-omada-controller: Docker image to run TP-Link Omada Controller (github.com)

 

Thanks & Regards,

Charitha

  0      
  0      
#1
Options
1 Accepted Solution
Re:Omada Software Controller Network topology not showing correctly-Solution
2024-08-05 08:52:35 - last edited 2024-08-15 08:28:48

 Hi @Charitha 

Did you also reboot the switch TL-SG1008P?

Please try the following:

1. clear the cache of the browser you are using and login the controller again;

2. Force Provision(Config > Manage Device > Force Provision) one EAP to have a test.

Recommended Solution
  0  
  0  
#4
Options
8 Reply
Re:Omada Software Controller Network topology not showing correctly
2024-08-05 06:55:02

Hi  @Charitha 

This may happen if the EAPs are not using the latest firmware version. Please check if the firmware is up-to-date.

How are the EAP units connected to the network and how did they power on?

  1  
  1  
#2
Options
Re:Omada Software Controller Network topology not showing correctly
2024-08-05 08:22:46

  @Vincent-TP 

 

Thanks for checking this out.

 

According to the Omada console, there is no any firmware upgrades available for both EAPs. Here is a screenshot of the firmware versions I have.

By the way, I was able to see the topology correctly up until a week ago without any issue under same software and firmware versions. I have tried restarting all the devices including the controller, but still I'm seeing above incorrect topology.

 

I have connected both EAPs via a TL-SG1008P, 8 Port Gigabit PoE Unmanaged Switch as follows.

 

ER605 ---> TL-SG1008P ---> EAP655 ---> ~10 wireless clients

                                        |---> Controller

                                        |---> Wired client (non PoE)

                                        |--->EAP615 ---> 1 wired client (non PoE)

                                                             |---> ~ 5 wireless clients

 

Thanks,

Charitha

  0  
  0  
#3
Options
Re:Omada Software Controller Network topology not showing correctly-Solution
2024-08-05 08:52:35 - last edited 2024-08-15 08:28:48

 Hi @Charitha 

Did you also reboot the switch TL-SG1008P?

Please try the following:

1. clear the cache of the browser you are using and login the controller again;

2. Force Provision(Config > Manage Device > Force Provision) one EAP to have a test.

Recommended Solution
  0  
  0  
#4
Options
Re:Omada Software Controller Network topology not showing correctly
2024-08-17 14:00:39

Hi  @Vincent-TP 

 

I tried steps you have mentioned above. But none of them solve the issue.

 

I have restared all the devices in the network including the switch. Further I tried force provisioning all the managed devices in the network. But non of them worked even I have tried to view the topology with a private window, and a different browser along with each steps.

 

Thanks,

Charitha

 

 

  0  
  0  
#5
Options
Re:Omada Software Controller Network topology not showing correctly
2024-08-17 14:25:01

  @Charitha 

 

Try and restart controller..

  0  
  0  
#6
Options
Re:Omada Software Controller Network topology not showing correctly
2024-08-17 15:56:33 - last edited 2024-08-17 15:57:17

@MR.S 

 

Already restarted all the device including the controller. But results are still the same. Not showing any of EAPs or wireless devices connected via EAPs.

 

Thanks,

Charitha

  0  
  0  
#7
Options
Re:Omada Software Controller Network topology not showing correctly
3 weeks ago

  @Charitha 

Thank all for the advise. 

I was very frustrated. But I did reset my OC200 controller and cleared the cache & Cookies and it worked flawlessly. Thank you all.

 

  1  
  1  
#8
Options
Re:Omada Software Controller Network topology not showing correctly
3 weeks ago

  @MR.S I was very frustrated. But I did reset my OC200 controller and cleared the cache & Cookies and it worked flawlessly. Thank you all.

  1  
  1  
#9
Options