Home Network Community > Wi-Fi Routers > Internet access fine from AX53 router but not from any clients
< Wi-Fi Routers

Internet access fine from AX53 router but not from any clients

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Internet access fine from AX53 router but not from any clients

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Internet access fine from AX53 router but not from any clients
Internet access fine from AX53 router but not from any clients
2024-12-05 15:34:48
Tags: #Network Connectivity
Model: Archer AX53  
Hardware Version:
Firmware Version:

Bought an AX53 to replace my ISP supplied Nokia router.

 

Tether app says everything is fine, all LEDs are green

 

From the router diagnostics page I can ping and traceroute to any external address and DNS resolves ok, but no clients can reach the internet.

 

All clients can connect to each other just not the outside world. This is the same for wifi or ethernet clients and for DHCP or static address.

 

A ping request from a client  to internet just hangs. A traceroute makes it as far as the router (default gateway) but no further.

 

Everything works perfectly if I plug the old ISP router in, but it's very basic.

 

It seems like a routing issue, but I can't seem to get to the bottom of it.

 

Any help gratefully received

  0      
 
  0      
 
#1
Options
6 Reply
Re:Internet access fine from AX53 router but not from any clients
2024-12-05 19:15:49

  @Boik 

 

Make sure that your ISP doesn't use any specific VLAN for Internet connection:

 

 

or ask your ISP if you need to use a router MAC clone feature:

 

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#2
Options
Re:Internet access fine from AX53 router but not from any clients
2024-12-05 21:27:25

  @Boik 

Ah, thanks, but VLAN isn't selected on the old router, and I tried it with the cloned MAC address out of desperation.

 

It's really got me puzzled.

  0  
  0  
#3
Options
Re:Internet access fine from AX53 router but not from any clients
2024-12-05 21:52:42

  @Boik 

 

In this case, if you can direcly replace your ISP router with AX53 and it has an Internet access, it would mean that any device connected by DHCP to the AX53 should have Internet access unless there's some kind of a DNS issue. Double check your AX53 configuration for any kind of mis-cofiguration (Access Control, Parental Controls, etc.).

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  1  
  1  
#4
Options
Re:Internet access fine from AX53 router but not from any clients
2024-12-06 07:02:00

  @Boik 

 

Hi, thanks for posting question here.

For your situation, it is suggested to follow this guide to troubleshoot:

What should I do if I cannot access the internet through Wi-Fi router?

Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode.
  0  
  0  
#5
Options
Re:Internet access fine from AX53 router but not from any clients
2024-12-06 16:42:31

  @Boik 

 

Thanks for the advice guys. I should get time to look at this tomorrow, so will report back.

  0  
  0  
#6
Options
Re:Internet access fine from AX53 router but not from any clients
2024-12-07 11:15:49

  @Boik 

 

Thanks for your patience guys, I got there in the end. After following all of the suggestions, and the video I still couldn't get to the bottom of it, so I did a factory reset and started again. Everything is now working as expected. The only difference THAT I AM AWARE OF is that I didn't apply the firmware update.

 

Obviously if there was a problem with the upadet then it would have affected everyone, and not jsut me.

 

I will run like this for a couple od days, and the  take a backup and apply the update. I'm confident it will be fine.

 

Once again, thanks for your help, and sorry for wasting your time.

  0  
  0  
#7
Options

Information

Helpful: 0

Views: 569

Replies: 6

Tags

Network Connectivity
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.