Home Network CommunityAdaptersTX50UH V1 will only connect if I reboot Sky Max hub router each time
Adapters

TX50UH V1 will only connect if I reboot Sky Max hub router each time

TX50UH V1 will only connect if I reboot Sky Max hub router each time

TX50UH V1 will only connect if I reboot Sky Max hub router each time
TX50UH V1 will only connect if I reboot Sky Max hub router each time
2025-12-18 10:57:16 - last edited 2026-01-08 11:46:02
Model: Archer TX50UH  
Hardware Version: V1
Firmware Version:

I purchased the TX50UH V1 which only connects if I reboot Sky Max hub router each time. Sometimes It does connect to the router but with no internet access as well.

 

The Sky Max Hub is locked down so you cannot amend channels and I have checked nothing is restricted.

(other devices connect fine via wifi)

 

I have tried:

  1. ipcong /release and /renew and dnsflush

  2. Amending preferred band on the adapter config

  3. Network reset

  4. Restarting adapter

  5. Rebooting PC

  6. Checked latest drivers (where were "2023 Archer TX50UH(US,EU,CA,JP) v1_5001.19.102.1_win10_win11")

  7. Tried setting DNS to 8.8.8.8 and 8.8.4.4

 

I am unsure what else to try? Help!

0
0
#1
1 Accepted Solution
Re:TX50UH V1 will only connect if I reboot Sky Max hub router each time-Solution
2025-12-24 02:59:03 - last edited 2026-01-08 11:46:02

Hello @Jonf64 ,

Welcome to our community.

 

Here are some suggestions that may help you:

  1. If your computer has a built-in Wi-Fi adapter, disable it to avoid possible interference.
  2. Move your TP-Link adapter closer to the router (ideally within 10-15 feet) to improve signal strength.
  3. Power-saving modes can sometimes cause disconnections. Make sure power-saving mode is disabled in Device Manager.
  4. If possible, connect the adapter to another network for comparison.

 

For detailed instructions, please refer to Case 2 on this FAQ page: What should I do if the TP-Link network adapter is not working properly in my computer?

Welcome to Our Community! Get the latest posts: △New Firmware for Archer GE550/GE650 V1 Introduces AI-QoS, EasyMesh IoT Expansion, and More! △New Firmware Releases for Archer BE805 V1/BE450 V1 to Support VPN Merge, New ECO Mode, and More! More posts, please see: △ Get the Ongoing Pre-release Firmware for Wi-Fi Routers Here— Subscribe for Updates! Urgent problems with your Wi-Fi Router, Range Extender, or DSL Modem? Please reach out via private Messages or @Joesph-TP in your new thread directly. Click △ Or ☆Recommended Solution if the post/answer helps.
Recommended Solution
0
0
#2
1 Reply
Re:TX50UH V1 will only connect if I reboot Sky Max hub router each time-Solution
2025-12-24 02:59:03 - last edited 2026-01-08 11:46:02

Hello @Jonf64 ,

Welcome to our community.

 

Here are some suggestions that may help you:

  1. If your computer has a built-in Wi-Fi adapter, disable it to avoid possible interference.
  2. Move your TP-Link adapter closer to the router (ideally within 10-15 feet) to improve signal strength.
  3. Power-saving modes can sometimes cause disconnections. Make sure power-saving mode is disabled in Device Manager.
  4. If possible, connect the adapter to another network for comparison.

 

For detailed instructions, please refer to Case 2 on this FAQ page: What should I do if the TP-Link network adapter is not working properly in my computer?

Welcome to Our Community! Get the latest posts: △New Firmware for Archer GE550/GE650 V1 Introduces AI-QoS, EasyMesh IoT Expansion, and More! △New Firmware Releases for Archer BE805 V1/BE450 V1 to Support VPN Merge, New ECO Mode, and More! More posts, please see: △ Get the Ongoing Pre-release Firmware for Wi-Fi Routers Here— Subscribe for Updates! Urgent problems with your Wi-Fi Router, Range Extender, or DSL Modem? Please reach out via private Messages or @Joesph-TP in your new thread directly. Click △ Or ☆Recommended Solution if the post/answer helps.
Recommended Solution
0
0
#2

Information

Helpful: 0

Views: 325

Replies: 1

About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.