Home Network Community > Wi-Fi Routers > After I reset, I couldn't switch the language in the management interface.
< Wi-Fi Routers

After I reset, I couldn't switch the language in the management interface.

After I reset, I couldn't switch the language in the management interface.

After I reset, I couldn't switch the language in the management interface.
After I reset, I couldn't switch the language in the management interface.
2026-01-05 14:08:18
Tags: #Web GUI Management
Model: Archer AX72  
Hardware Version: V1
Firmware Version: 1.4.5 Build 20250928 rel. 17568 (4555)

I found that after the update, my AX72 It is very easy to appear CPU 100% of the time.

 

Therefore, I reset the settings to factory defaults. However, when I tried to change the language of the device management interface to Chinese after the reset, I found that the language was not changed after selecting it. Is there a firmware update that can solve this problem?

  1      
 
  1      
 
#1
Options
5 Reply
Re:After I reset, I couldn't switch the language in the management interface.
2026-01-07 05:47:40

Hello @PokoTW ,

Welcome to our community.

 

For CPU usage, have you run any high-traffic activity? Or add any new client to the network?

For the language, please go to Advanced->System->Time& Language. The Chinese option should be the last.

 

Welcome to Our Community！ Check Out the Latest Posts: △New Firmware for Archer BE800 V1 to Support VPN Merge, EasyMesh Guest/IoT Network Extend, and More △Enhanced EasyMesh Support with Extended Guest/IoT/MLO Networking and Advanced Features for BE550 V2 △New Firmware for Archer BE900 V2 to Support Multi-WAN, DoH/DoT, EasyMesh in AP Mode and More △New Firmware for Archer BE260/Archer BE400 to Support VPN Merge, New ECO Mode, and More If you found the post or response helpful, click Helpful. If an answer solves your problem, click Recommended Solution so that others can benefit from it.
  1  
  1  
#2
Options
Re:After I reset, I couldn't switch the language in the management interface.
2026-01-07 10:12:11

  @Joseph-TP Thank you for your reply. The language setting here is working fine, but the language options in the upper right corner are not responding.

 

Additionally, I found that the processor speed suddenly spiked when I entered the following screens, and the screen data loaded very slowly.

 

 

  0  
  0  
#3
Options
Re:After I reset, I couldn't switch the language in the management interface.
2026-01-08 03:03:09 - last edited 2026-01-08 03:04:03

Hello @PokoTW ,

 

Does the CPU usage surge only occur when you try to log in to the router's web interface? Please confirm that you have connected to the router's WiFi, and turn off the mobile data.

After successfully logging into the router's web interface, will CPU usage decrease? Besides this, will internet usage be significantly affected?

Welcome to Our Community！ Check Out the Latest Posts: △New Firmware for Archer BE800 V1 to Support VPN Merge, EasyMesh Guest/IoT Network Extend, and More △Enhanced EasyMesh Support with Extended Guest/IoT/MLO Networking and Advanced Features for BE550 V2 △New Firmware for Archer BE900 V2 to Support Multi-WAN, DoH/DoT, EasyMesh in AP Mode and More △New Firmware for Archer BE260/Archer BE400 to Support VPN Merge, New ECO Mode, and More If you found the post or response helpful, click Helpful. If an answer solves your problem, click Recommended Solution so that others can benefit from it.
  0  
  0  
#4
Options
Re:After I reset, I couldn't switch the language in the management interface.
2026-01-13 14:02:59 - last edited 2026-01-13 14:03:13

@Joseph-TP Thank you, the language issue has been resolved, and I can switch normally now.

The CPU issue was correct; it only occurred when I tried to log into the router's web interface, and then it would drop again. However, it took longer than previous versions to retrieve device IP information or client details from the webpage.

  0  
  0  
#5
Options
Re:After I reset, I couldn't switch the language in the management interface.
3 weeks ago

Hi@PokoTW ,

Have you compared with the Tether App management page? 

If your network usage is not significantly affected, I suggest you continue to monitor the router.

I will also report this to the relevant department to confirm whether any areas need improvement.

 

Thanks again for your feedback.

Welcome to Our Community！ Check Out the Latest Posts: △New Firmware for Archer BE800 V1 to Support VPN Merge, EasyMesh Guest/IoT Network Extend, and More △Enhanced EasyMesh Support with Extended Guest/IoT/MLO Networking and Advanced Features for BE550 V2 △New Firmware for Archer BE900 V2 to Support Multi-WAN, DoH/DoT, EasyMesh in AP Mode and More △New Firmware for Archer BE260/Archer BE400 to Support VPN Merge, New ECO Mode, and More If you found the post or response helpful, click Helpful. If an answer solves your problem, click Recommended Solution so that others can benefit from it.
  0  
  0  
#6
Options

Information

Helpful: 1

Views: 221

Replies: 5

Tags

Web GUI Management
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.