Home Network Community > Access Points > VLAN on TL-WA701ND seems not working properly
< Access Points

VLAN on TL-WA701ND seems not working properly

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

VLAN on TL-WA701ND seems not working properly

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
VLAN on TL-WA701ND seems not working properly
VLAN on TL-WA701ND seems not working properly
2016-03-16 21:15:41
Model :

Hardware Version : Not Clear

Firmware Version :

ISP :

Hi everyone. I'm a newbie here and any help would be greatly appreciated.

I'm configuring a TL-WA701ND with Multi-SSID (SSID1, SSID2, SSID3 and SSID4 with respective VLANs 1, 2, 3, and 4). This AP is connected to an 802.1Q configured trunk port of a NetGear switch (port 8) whose PVID is set to 1. The NetGear switch's port 8 is tagged on VLANs 1, 2, 3, and 4 as what is advised on the User's Guide. NetGear's port 8 is another trunk with similar config as port 7 and is connected to a firewall that also do 802.1Q. VLAN 1 is 192.168.1.0/24, VLAN 2 is 192.168.2.0/24, VLAN 3 is 192.168.3.0/24 and finally VLAN 4 is 192.168.4.0/24. Each VLAN has its own DHCP service provided by the firewall.

Here's my problem: If i connect to SSID1 i have no issues. I can get IP address from the correct pool (192.168.1.x/24). Connecting to SSIDs 2 to 4 however cannot acquire an IP address. But if i change the PVID of port 8 to 2 and connect to SSID2 i can get an IP from the correct pool (192.168.2.x/24). Connecting to SSIDs 1, 3, and 4 however cannot acquire IP address. Same is true if i change the PVID to 3 and 4. Note that i can authenticate to all SSIDs but the problem lies on the DHCP negotiation.

Does anyone experience this problem?

Here are my other details:
Firmware Version: 3.17.0 Build 140324 Rel.36563n
Hardware Version: WA701ND v2 00000000

Thanks in advance for your help.
  0      
 
  0      
 
#1
Options
10 Reply
Re:VLAN on TL-WA701ND seems not working properly
2016-03-18 10:43:46
It doesn't make sense. And I don't think there are any problem with the 701ND. So you would better check the configuration of the port 7 and whether your firewall support VLAN? Or you could tell us the configruration of your firewall and the NetGear switch. Then maybe i could find the problem for you.
  0  
  0  
#2
Options
Re:VLAN on TL-WA701ND seems not working properly
2016-03-18 19:19:20
I'm pretty sure the firewall (WatchGuard) and the switch (NetGear) VLAN configuration works. Btw, the switch's port 1 is configured as VLAN1, port 2 = VLAN2, port 3 = VLAN3, and port 4 = VLAN4. Connecting computers via these ports (wired) get the correct DHCP IP Address. Been doing this type of config for years. Done this with other Access Points that does multi-SSID with VLANs and never had this issue. I'm looking at the WA701ND as a more cost effective alternative.
  0  
  0  
#3
Options
Re:VLAN on TL-WA701ND seems not working properly
2016-03-30 23:15:08
The problem has been fixed by updating the firmware using a beta version provided by TP Link support. Now waiting for the official release of the firmware version.
  0  
  0  
#4
Options
Re:VLAN on TL-WA701ND seems not working properly
2016-05-16 17:04:28
I appear to have the same issue with the TL-WA801ND. Is the firmware now officially released or can a link be provided for the beta download - thanks.
  0  
  0  
#5
Options
Re:VLAN on TL-WA701ND seems not working properly
2016-05-17 09:17:26
You could better send email to support.tp-link.com for help. And you could tell your situation clearly with network topology and configurations, maybe the problem isn't blame to that.
  0  
  0  
#6
Options
VLAN on TL WA701ND seems not working pro
2016-07-28 01:40:50
Its hard to visualise what you are saying is wrong. Can you post a screenshot? It might helpColm
  0  
  0  
#7
Options
Re:VLAN on TL-WA701ND seems not working properly
2016-07-28 19:27:13
Open a Ticket at ticket.tp-link.com.
It looks like the Multi SSID feature (especially the tagging) is not working correctly on many TP-Link products.

For security reasons i would send all untagged traffic on a trunk to a non existing or unused VLAN.
  0  
  0  
#8
Options
VLAN on TL WA701ND seems not working pro
2016-08-03 20:58:36
As Andy says, NXJMonitor does not work for i2c sensors link the ultrasonic sensor. It should work for the touch sensor and other analog sensors.
  0  
  0  
#9
Options
Re:VLAN on TL-WA701ND seems not working properly
2018-01-05 22:45:54

cza wrote

Model :

Hardware Version : Not Clear

Firmware Version :

ISP :

Hi everyone. I'm a newbie here and any help would be greatly appreciated.

I'm configuring a TL-WA701ND with Multi-SSID (SSID1, SSID2, SSID3 and SSID4 with respective VLANs 1, 2, 3, and 4). This AP is connected to an 802.1Q configured trunk port of a NetGear switch (port 8) whose PVID is set to 1. The NetGear switch's port 8 is tagged on VLANs 1, 2, 3, and 4 as what is advised on the User's Guide. NetGear's port 8 is another trunk with similar config as port 7 and is connected to a firewall that also do 802.1Q. VLAN 1 is 192.168.1.0/24, VLAN 2 is 192.168.2.0/24, VLAN 3 is 192.168.3.0/24 and finally VLAN 4 is 192.168.4.0/24. Each VLAN has its own DHCP service provided by the firewall.

Here's my problem: If i connect to SSID1 i have no issues. I can get IP address from the correct pool (192.168.1.x/24). Connecting to SSIDs 2 to 4 however cannot acquire an IP address. But if i change the PVID of port 8 to 2 and connect to SSID2 i can get an IP from the correct pool (192.168.2.x/24). Connecting to SSIDs 1, 3, and 4 however cannot acquire IP address. Same is true if i change the PVID to 3 and 4. Note that i can authenticate to all SSIDs but the problem lies on the DHCP negotiation.

Does anyone experience this problem?

Here are my other details:
Firmware Version: 3.17.0 Build 140324 Rel.36563n
Hardware Version: WA701ND v2 00000000

Thanks in advance for your help.


Sorry to bring back an old thread but I have EXACTLY this problem on a 801ND. I can see from the DHCP server that the correct leases are being offered but the client requests a VLAN1 ip resulting in a DHCPNACK response. Static IP doesn't work either. It's as if the AP is tagging the DHCP request but not the rest of the traffic. I'd be very interested in any firmware that resulted in this being resolved. Support requested my response and don't seem to have paid any attention to my explaining that the rest of the network is working perfectly with the VLANS. I've sent them my topology but anticipate days of back and forth. Currently considering just putting DD-WRT on,
  0  
  0  
#10
Options
Re:VLAN on TL-WA701ND seems not working properly
2018-02-11 23:50:10

pauldsmyth wrote

Sorry to bring back an old thread but I have EXACTLY this problem on a 801ND. I can see from the DHCP server that the correct leases are being offered but the client requests a VLAN1 ip resulting in a DHCPNACK response. Static IP doesn't work either. It's as if the AP is tagging the DHCP request but not the rest of the traffic. I'd be very interested in any firmware that resulted in this being resolved. Support requested my response and don't seem to have paid any attention to my explaining that the rest of the network is working perfectly with the VLANS. I've sent them my topology but anticipate days of back and forth. Currently considering just putting DD-WRT on,


Did support ever get back to you? I'm having a similar issue as well on a TP-LINK AP300. I have updated the AP to latest firmware.
  0  
  0  
#11
Options

Information

Helpful: 0

Views: 1624

Replies: 10

Related Articles
 TL-WA801ND as Universal Repeater seems not working
1597 0
 TL-WA901ND seems to be working but ...Help please!
595 0
TL-WA701ND with PoE
978 0
 how do i know if my TL-WA801ND is working properly as an extender?
1887 0
TL-WN881ND not working properly on Windows 10.
9650 0
 TL-WA854RE not working properly
752 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.