Home Network Community > All Threads > Instability for all wireless devices when one of them moves far away
< All Threads

Instability for all wireless devices when one of them moves far away

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Instability for all wireless devices when one of them moves far away

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Instability for all wireless devices when one of them moves far away
Instability for all wireless devices when one of them moves far away
2019-09-11 20:13:28 - last edited 2019-09-11 20:17:42
Model: Archer C60  
Hardware Version: V1
Firmware Version: 1.0.1 Build 20160919 rel.42470

Hello!

 

It took me a while to figure out what was causing the problem.

I live in a 2-story apartment, and when someone uses a phone or a laptop in a distant room, my wireless connection gets unstable.

 

This is my PC (connected to Wi-Fi) - ping my router while I walk away with my phone while watching a live stream:

 

I have tried updating the firmware, and it says it is up to date.

 

  • Channel width is at 20 MHz;
  • Transmission power is marked as "high";
  • 2.4 GHz mode is at 802.11b/g/n;
  • Channel is 11 (which is the best here);
  • QoS - priority for my PC is set to "high";
  • DoS protection is off;
  • Beacon interval is set to 100;
  • RTS Threshold is set to 2346;
  • DTIM interval is set to 1.

 

Does anybody know how to solve this?

Please let me know if I need to provide additional info.

 

Thanks in advance!

  0      
 
  0      
 
#1
Options
4 Reply
Re:Instability for all wireless devices when one of them moves far away
2019-09-12 02:05:38

@guismiti 

 

What is the stability of the wireless connection when you are in the same floor with the Archer C60? 

 

If it works well but became unstable in a distant room, it seems like that the environment interference affects its performance, like the distance and obstacles. 

 

To solve it, you can add a network expansion device to extend the wifi range and eliminate the wifi dead zone. Like the range extender and powerline adapters.

Note: It is suggested to use powerline adapters when the whole house running under the same power circuit cause they communicate with each other via power line.

 

Best regards. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  1  
  1  
#2
Options
Re:Instability for all wireless devices when one of them moves far away
2019-09-13 14:24:17 - last edited 2019-09-13 14:38:22

@Kevin_Z 

Thank you for your reply!

 

I do have a repeater here, but it doesn't solve my problem - whenever someone leaves home with a phone, I get latency spikes.

 

What I want is for the router to stop overloading (or whatever is happening) when someone has a poor signal - just drop the weak connection or limit some parameter related to packets, but I have poor knowledge to know what to do.

 

Edit: I just noticed that the router's CPU usage goes up near 100% when I walk away with my phone.

 

Edit #2: I tried to set transmission power to medium or low, and also set RTS threshold to 500, but nothing worked.

  0  
  0  
#3
Options
Re:Instability for all wireless devices when one of them moves far away
2019-09-19 20:14:28

Can anybody help me?

Did I buy a not-very-cheap router that will overload and simply not work properly when a device is in the edge of its reach?

Or is there some setting that will help me avoid overloading? (even if it means dropping the connections that are causing it)

  0  
  0  
#4
Options
Re:Instability for all wireless devices when one of them moves far away
2019-09-30 19:23:35

@guismiti I still haven't found a solution

  0  
  0  
#5
Options

Information

Helpful: 0

Views: 796

Replies: 4

Related Articles
Devices only linking to one of my nodes
1505 0
How Many Devices Can Connect to One Wireless Router Handle?
6511 0
Poor wireless on new router on one device
1257 0
Disable wifi on one of the devices
567 0
One Devices has limited Download
548 0
Router not connecting to one website
423 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.