Home Network Community > All Threads > MODEL ARCHER VR1200 V.1.0 - no internet on 2.4ghz
< All Threads

MODEL ARCHER VR1200 V.1.0 - no internet on 2.4ghz

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

MODEL ARCHER VR1200 V.1.0 - no internet on 2.4ghz

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
MODEL ARCHER VR1200 V.1.0 - no internet on 2.4ghz
MODEL ARCHER VR1200 V.1.0 - no internet on 2.4ghz
2019-12-09 09:17:20 - last edited 2019-12-10 03:26:12
Model: AC50  
Hardware Version: V1
Firmware Version: 181217
Good morning,

MODEL ARCHER VR1200 V.1.0

I performed the installation as instructed.
I have done the firmware upgrade.
I have tried several times to reset to factory settings and to repeat the installation.
Nevertheless the result does not change.
All the devices connected in 5Ghz correctly browse the internet while for devices connected in 2.4ghz (any OS: windows, linux, android) it is showed that internet connection is not available. I can't even connect to the TPLink configuration interface even if connected in 2.4ghz.
In the control panel the wifi in 2.4ghz is correctly enabled (default settings).
In some cases, although everything is enabled, the 2.4ghz channel is not detected by the devices and not even the light on the modem is on (while for the 5. ghz there are no problems).

 

How could I solve?

  0      
 
  0      
 
#1
Options
2 Reply
Re:MODEL ARCHER VR1200 V.1.0 - no internet on 2.4ghz
2019-12-09 14:03:28 - last edited 2019-12-10 03:26:12

@TheRiddle You may have  bad unit. First try changing the channel from auto to one of the available channels and also the channel width. You may be on a channel that has some type of interference in your house. Do not hide SSID (enable) and use different SSID names. Be sure the mode is 11bgn.  Leave WDS off for now. Disable any MAC filtering.

  0  
  0  
#2
Options
Re:MODEL ARCHER VR1200 V.1.0 - no internet on 2.4ghz
2019-12-10 03:25:54 - last edited 2019-12-10 03:26:12

@TheRiddle 

 

Please ensure that the 2.4GHz wifi network has been enabled and do not hide SSID; try to change the wireless settings to give it a go, including the wireless network name and channel, like channel 1, 6 and 11. 

 

When it is connected but no internet access, please click here to get the IP address and gateway. 

 

And then try to ping the gateway of the Archer VR1200, which is 192.168.1.1 by default and show us the results. 

 

Try to change another wireless device to verify whether it has the same issue. And ensure that the firmware of the VR1200 is up to date.

 

Besides, when and where did you buy this Archer VR1200?

 

Good day. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#3
Options

Information

Helpful: 0

Views: 1178

Replies: 2

Related Articles
Deco X50 v.1.2 vs v.1.0
313 0
Support for Archer VR1200
684 0
the problem for update w8901 n v 1.0
455 0
Archer C50 - Frequent Internet Disconnection Issue on 2.4GHz
635 0
DSL modem Archer VR1200
800 0
Archer VR1200 Port forwarding
1121 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.