Maiking a Slave Deco the Main Deco - Why?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Maiking a Slave Deco the Main Deco - Why?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Maiking a Slave Deco the Main Deco - Why?
Maiking a Slave Deco the Main Deco - Why?
2019-12-12 07:24:42 - last edited 2019-12-16 06:44:54
Model: Deco M4  
Hardware Version: V20
Firmware Version: (purchased/own but haven't installed yet)

[I own but have not yet opened or installed, a Deco M4 system.]

A TP-Link FAQ for the Deco units states, "For some reason, if you want to change the slave Deco to work as the Main Deco but do not want to reset the whole Deco network and reconfigure it, you can refer to the following instruction to finish the setup process."

 

The instructions certainly go on to tell you how to do it, but what would "some reason" be?  Is there some advantage to making a slave Deco the Main Deco?  Would it get a stronger signal if it was designated the Main Deco?  I ask because when I install my system in a few days, the Main Deco will start off next to my modem, in a room where I don't require a good WiFi signal.  The place where I'll place one of the two Deco "slaves" is at the end of my house where there are several WiFi devices that would benefit from a better signal.  Obviously I'm just wondering what the benefit of changing the designations would be, if any (and I'd have to suppose there would be one or two, or why is this available to do, right?).

  0      
  0      
#1
Options
1 Accepted Solution
Re:Maiking a Slave Deco the Main Deco - Why?-Solution
2019-12-13 02:36:38 - last edited 2019-12-16 06:44:54

@DroMike 

 

It can be that the end users just want to swap the location of the main Deco and slave Deco; or the current network diagram may have some problem, like unstability or slow speed; changing slave Deco to main Deco is a troubleshooting method to narrow down the issue-- whether it is the Deco itself or the actual network environment. 

 

The actual performance is related to the network environment, including the modem, distance, obstacles and interferences. Changing slave Deco simply won't strenghthen the wifi signal. Please notice that there is no other factors changed, except the location of slave/main Deco. 

 

Good day. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
3 Reply
Re:Maiking a Slave Deco the Main Deco - Why?-Solution
2019-12-13 02:36:38 - last edited 2019-12-16 06:44:54

@DroMike 

 

It can be that the end users just want to swap the location of the main Deco and slave Deco; or the current network diagram may have some problem, like unstability or slow speed; changing slave Deco to main Deco is a troubleshooting method to narrow down the issue-- whether it is the Deco itself or the actual network environment. 

 

The actual performance is related to the network environment, including the modem, distance, obstacles and interferences. Changing slave Deco simply won't strenghthen the wifi signal. Please notice that there is no other factors changed, except the location of slave/main Deco. 

 

Good day. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
Re:Maiking a Slave Deco the Main Deco - Why?
2019-12-13 02:49:08

OK - thanks Kevin. - Mike

  0  
  0  
#3
Options
Re:Maiking a Slave Deco the Main Deco - Why?
2019-12-16 06:44:46

@DroMike 

 

You are welcome. It is glad to help you. 

 

If need more help in the future, do not hesitate to contact us. 

 

Good day. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options