How to check network strength on TP Link Admin Panel

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

How to check network strength on TP Link Admin Panel

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
How to check network strength on TP Link Admin Panel
How to check network strength on TP Link Admin Panel
2020-05-18 08:35:50
Model: Archer MR400  
Hardware Version: V1
Firmware Version: 1.5.0 0.9.1 v0001.0 Build 180720 Rel.63339n

Hello, 

 

I have an TP Link 4G LTE Archer MR400 Router. 

 

I'm planning to replace my exisiting extrernal antennas by 2 x LPDA 12 Dbi Antenna. Attaching picture below. 

 

Just wanted to know is there any way in which I can check actual signal strength instead of percentage on TP Link Admin Panel ? So that i will get to know I have setup my external antenna correctly ?

 

Views & Ideas Most Welcome. Thanks in Advance :)

  0      
  0      
#1
Options
5 Reply
Re:How to check network strength on TP Link Admin Panel
2020-05-18 09:46:11

@amolkalhapure I believe in the 'Advanced' tab you should also see RSRP, RSRQ & SNR values, which are all related to your signal strength.  Use the following chart to help:

 

 

                                              RSRP(dBM)       RSRQ(dB)     SNR(dB)    

(RF Conditions)  Excellent       >=-80                  >=-10            >=20

(RF Conditions)  Good            -80 to -90          -10 to -15      13 to 20

(RF Conditions)  Mid Cell       -90 to -100         -15 to -20       0 to 13

(RF Conditions)  Cell Edge      <=-100                <=-20            <=0

 

I currently get the following:    -97dBM               -8dB             18.2dB

 

CheerZ

 

 

  3  
  3  
#2
Options
Re:How to check network strength on TP Link Admin Panel
2020-05-18 13:33:32

@Fl1nst0ne Hello, Thanks for reply but it seems my admin panel don't have that ? :( 

 

Can you throw some more light on this ?

  0  
  0  
#3
Options
Re:How to check network strength on TP Link Admin Panel
2020-05-18 14:41:47 - last edited 2020-05-18 14:42:28

@amolkalhapure I only have the MR600 router but use to have the MR200 router and both have these values listed under the 'Advanced' tab.  I made a presumption that the MR400 router also llisted these values.  Have you upgraded to the latest firmware?

 

CheerZ

  0  
  0  
#4
Options
Re:How to check network strength on TP Link Admin Panel
2020-05-20 12:04:34

@Fl1nst0ne Hello, Just returned MR400 & ordered MR600 :)

  0  
  0  
#5
Options
Re:How to check network strength on TP Link Admin Panel
2020-12-26 23:18:47

@amolkalhapure Hi I have mr200 V2 as well. I don't see any dBi values like RSRQ, RSRP, SINR in my admin page too. After you buy MR600 could you access these dBi values? Is there any chance to access values without changing the product. Because I am happy with mr200 normally accept the dBi values.

 

By the way could you have chance to try your LPDA antennas. How much dBi could you gain with it. Could you share please. Thanks

  0  
  0  
#6
Options

Information

Helpful: 0

Views: 10099

Replies: 5

Related Articles