Home

Forums

Stories

Knowledge Base

Home Network Community > All Threads > Archer VR400 / AC1200 Bridge Mode / modem only for use with Deco

< All Threads

Archer VR400 / AC1200 Bridge Mode / modem only for use with Deco

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer VR400 / AC1200 Bridge Mode / modem only for use with Deco

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

nicka777

2020-06-22 07:01:20 - last edited 2020-06-23 08:16:52

Posts: 6

Helpful: 1

Solutions: 1

Stories: 0

Registered: 2020-06-22

Archer VR400 / AC1200 Bridge Mode / modem only for use with Deco

2020-06-22 07:01:20 - last edited 2020-06-23 08:16:52

Model: Archer VR400

Hardware Version:

Firmware Version:

Hi All,

I have recently purchased a VR400 to replace my ISP's Bt Home Hub 5 for use with Deco M5 Mesh. I understood that, in order for the mesh to work in 'Router Mode' and get all the functions, I needed to put my existing Modem/Router in 'bridge' mode or 'modem only' mode. Apparently the BT HH5 doesnt support this so I went with the VR400 which supposedly does.

Im using BT internet (VDSL)

Can someone guide me what exactly this means on the VR400 ? Ive set it up following the wizard then disabled wifi but this doesnt seem to be the same thing as mentioned here

https://community.tp-link.com/en/home/forum/topic/179144.

The deco is working in 'router' mode but seems that both deco and VR400 are still handing DHCP which doesnt seem right.

Although most connected devices on the are working OK, some things, such as Spotify Connect 'seeing' devices on which to play music (amazon eco / sonos...), are not.

Im no networking expert so be gentle !

thanks

Nick

1 Accepted Solution

nicka777

LV1

2020-06-23 07:48:17 - last edited 2020-06-23 08:16:52

Posts: 6

Helpful: 1

Solutions: 1

Stories: 0

Registered: 2020-06-22

Re:Archer VR400 / AC1200 Bridge Mode / modem only for use with Deco-Solution

2020-06-23 07:48:17 - last edited 2020-06-23 08:16:52

@Solla-topee

ok - made the changes last night and worked fine in the end.

Initially I didnt enable or add anything in VLAN but then found that for BT Infinity is needed value '101'

thanks for your help

Recommended Solution

8 Reply

Solla-topee

2020-06-22 07:20:37 - last edited 2020-06-22 07:21:34

Posts: 13387

Helpful: 2308

Solutions: 1925

Stories: 8

Registered: 2020-05-19

Re:Archer VR400 / AC1200 Bridge Mode / modem only for use with Deco

2020-06-22 07:20:37 - last edited 2020-06-22 07:21:34

@nicka777

Hi, did you refer to the FAQ below to configure the VR400 as a pure modem?

How can I set up my TP-Link modem router as a pure modem?

If yes, there won't be two DHCP servers in the LAN. You may set up the main Deco in Router mode like below:

Deco Setup Walkthrough

>>Landscape Mode - Tapo App for Pad. >>Smart Action 2.0 Explore and meet the next level home automation. >>How to position my TP-Link camera for optimal performance.

nicka777

LV1

2020-06-22 07:52:11

Posts: 6

Helpful: 1

Solutions: 1

Stories: 0

Registered: 2020-06-22

Re:Archer VR400 / AC1200 Bridge Mode / modem only for use with Deco

2020-06-22 07:52:11

@Solla-topee

ok - thanks - I didnt see that.

But what about the existing connections ? Do I delete them first (or after?) or leave them there ?

If I delete them, where do I enter the username and password for my ISP ?

Nick

Solla-topee

2020-06-22 08:05:05

Posts: 13387

Helpful: 2308

Solutions: 1925

Stories: 8

Registered: 2020-05-19

Re:Archer VR400 / AC1200 Bridge Mode / modem only for use with Deco

2020-06-22 08:05:05

@nicka777

Hi, you can delete them and enter your internet credentials on the Deco WAN (when configuring the Deco to work as a router, choose PPPoW in the WAN setup).

>>Landscape Mode - Tapo App for Pad. >>Smart Action 2.0 Explore and meet the next level home automation. >>How to position my TP-Link camera for optimal performance.

nicka777

LV1

2020-06-22 08:20:51 - last edited 2020-06-22 08:22:20

Posts: 6

Helpful: 1

Solutions: 1

Stories: 0

Registered: 2020-06-22

Re:Archer VR400 / AC1200 Bridge Mode / modem only for use with Deco

2020-06-22 08:20:51 - last edited 2020-06-22 08:22:20

@Solla-topee

thanks again. Ill have to try this tonight when no one else is online.

I spent hours configuring all the (40+) devices on the deco over the weekend. Is there a way to do this without a factory reset and starting over ?

I did find 'bridge' somewhere on the quick setup when I first set up the router but the deco wouldnt connect at all. Just showed a red light.

On the deco app under 'More' icon (bottom menu) then 'advanced' then 'IPv4' then click the current selection ('Dynamic IP') then 'Internet Connection Type' (now shows WAN at top of page) are the following choices:

Dynamic IP
Static IP
PPPoE
L2TP
PPTP
DS-Lite

I assume its then PPTP ?

Do I do this before or after setting the VR400 as bridge ? If after, wont I have lost access to the deco on doing this on the router ?!

I dont want to get locked out of the deco and having to reset it !

apologies for all the questions !

Solla-topee

2020-06-22 08:35:00

Posts: 13387

Helpful: 2308

Solutions: 1925

Stories: 8

Registered: 2020-05-19

Re:Archer VR400 / AC1200 Bridge Mode / modem only for use with Deco

2020-06-22 08:35:00

@nicka777

Hi, you may change the VR400 to a pure/bridge modem first, then change the 'Internet Connection Type' on the Deco app for the main Deco unit to PPPoE, then input the internet credentials (username and password) and it should be connecting, there is no need to reset all Decos.

>>Landscape Mode - Tapo App for Pad. >>Smart Action 2.0 Explore and meet the next level home automation. >>How to position my TP-Link camera for optimal performance.