Home Network Community > All Threads > Ax 50 Performance issues
< All Threads

Ax 50 Performance issues

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Ax 50 Performance issues

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Ax 50 Performance issues
Ax 50 Performance issues
2020-07-12 14:50:16
Model: Archer AX50  
Hardware Version: V1
Firmware Version: Latest

Can someone tell me why this router with 4 antennas performs slower than my virgin media superhub 3?

 

I can barely max out my 200mbit connection with this thing on 5Ghz in the same room a couple of metres away from the router yet the superhub 3 I can get the full 200mbit in the bathroom upstairs.

 

Not good may have to go back to Argos considering it's been opened already I should have known and demanded a replacement, don't think I'll bother it performs woefully.

  0      
 
  0      
 
#1
Options
9 Reply
Re:Ax 50 Performance issues
2020-07-13 09:45:27

@Adrian1976 

 

Hello,

 

May I have your detailed network topology, like how this router and virgin media hub connected?

 

Have you ever changed any advanced setting on it web UI which may affect your internet speed? If you are not sure, it is suggested to reset it to factory defaults and set up the internet again from its web UI and leave all the other settings by default.

 

Please also confirm what is the wired speed you can get when you connect one computer only to the AX50 with an Ethernet cable and leave all others disconnected, run the speed test again.

 

If the above test result is acceptable, please confirm again what is the 5G client model and try to get another device to do a simple comparison. Also, please check what is the negotiation link speed on that device as well as on this 5G one.

 

Thanks.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:Ax 50 Performance issues
2020-07-13 10:28:16

@Kevin_Z 

 

I have the virgin superhub 3 in modem mode as indicated by the red light, I only use 5g, 2.4ghz is disabled, my phone is the new One plus 8 pro which supports WiFi 6 AX everything is auto on 5gjz band, I've tried adjusting bandwidth to 160mhz that made it slower which is backwards when my client supports AX.

 

Cable connection to PC speed is fine but wireless is slower than the hub 3 at the same distance, the router is positioned in the same place.

  0  
  0  
#3
Options
Re:Ax 50 Performance issues
2020-07-13 10:33:11

@Kevin_Z 

 

Here's an example, full signal, about 4 metres away from the router, yet the most it can manage on my 200mbit connection is 160-180 I get full 200mbit speed on the superhub 3 at the same distance.

 

Link speed is 720 sometimes 1200 not that makes any difference to the end result.

File:
Screenshot_20200713-112852~2.jpgDownload
  0  
  0  
#4
Options
Re:Ax 50 Performance issues
2020-07-13 10:33:27

@Adrian1976 

 

 

File:
Screenshot_20200713-112958.jpgDownload
  0  
  0  
#5
Options
Re:Ax 50 Performance issues
2020-07-13 10:34:17

@Adrian1976 

 

As you can see it's full signal.

File:
Screenshot_20200713-112843.jpgDownload
  0  
  0  
#6
Options
Re:Ax 50 Performance issues
2020-07-14 04:16:04

@Adrian1976 

 

Hello, thanks for the detailed info.

 

How about the QoS setting on the AX50? It is suggested to check and ensure the QoS is on the Standard Mode (on the Tether Homecare page-QoS), then get back to the Clients' page, check all the clients connected to the router and ensure the High Priority is disabled.

 

Or, it would be easier to reset the AX50 to factory defaults and set it up from the scratch, leave all the settings by default and check the results again.

 

If the above suggestions don't make any difference, please try to change the channel width for the 5G to 80MHz, reboot the AX50 and check again.

 

Thanks.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#7
Options
Re:Ax 50 Performance issues
2020-07-19 19:36:02
Quiero comprar un routers ax50 y tengo contratado 120 megas de bajada. La idea es conectarlo a mi notebook por wifi con el adaptador Killer 1550i ac tiene canal 160 mhz. Me va a servir este router? Entiendo que depende la distancia. Va a rendir bien este router para eso? O es preferible un archer C80 de tp link?? Gracias voy a poder utilizar el canañ 160 con wiffi 5 eso mejora la calida y ??
  0  
  0  
#8
Options
Re:Ax 50 Performance issues
2020-12-31 10:45:49

@Kevin_Z hi kevin, when using lan i can get max out to my plan 500Mbps but whyn im using 5Ghzand beside the router it's hardly to even reach to 300Mbps even only using 1 device, hope you can help me.I'm using AX50 just arrived yest

  0  
  0  
#9
Options
Re:Ax 50 Performance issues
2021-01-04 02:52:44

@nvdhey 

 

Hi, have you checked my previous suggestions to Adrian1976? Give that a go, then confirm, thanks.

Kevin_Z wrote

@Adrian1976 

 

Hello, thanks for the detailed info.

 

How about the QoS setting on the AX50? It is suggested to check and ensure the QoS is on the Standard Mode (on the Tether Homecare page-QoS), then get back to the Clients' page, check all the clients connected to the router and ensure the High Priority is disabled.

 

Or, it would be easier to reset the AX50 to factory defaults and set it up from the scratch, leave all the settings by default and check the results again.

 

If the above suggestions don't make any difference, please try to change the channel width for the 5G to 80MHz, reboot the AX50 and check again.

 

Thanks.

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#10
Options

Information

Helpful: 0

Views: 1745

Replies: 9

Related Articles
AX 50 Heat Issue
28558 8
Archer AX-50 and poor ethernet speeds
757 0
AX 50 Recurrent WAN / internet disconnection
2623 1
The AX-55 is a slap in the face to AX-50 owners struggling with overheating issues.
1631 3
Tplink Archer Ax-50
1077 0
Change router tp-link AX 50 wpa2 to wpa3
1361 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.