Home Network Community > All Threads > VR400 Firmware Upgrade = No VDSL connection
< All Threads

VR400 Firmware Upgrade = No VDSL connection

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

VR400 Firmware Upgrade = No VDSL connection

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
VR400 Firmware Upgrade = No VDSL connection
VR400 Firmware Upgrade = No VDSL connection
2020-08-02 16:28:36 - last edited 2020-08-03 07:24:11
Model: Archer VR400  
Hardware Version: V2
Firmware Version: 0.6.6 0.9.1

When I upgraded the modem to the July 2020 firmware release, I was not able to establish an internet connection (Plusnet UK)

 

The line was syncing but WAN status was 'Disconnected'

 

Suggest you dont upgrade firmware until this problem is fixed.

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:VR400 Firmware Upgrade = No VDSL connection-Solution
2020-08-03 07:24:00 - last edited 2020-08-03 07:24:11

@jpuk

Hello!

After the firmware update, did you try to reset the modem and set up the internet connection type again?

And may I know what kind of connection type did you use for Plusnet, PPPOE? Do you also need Vlan ID?

If possible, can I have a picture of the DSL status page, such as:

 

Thank you very much~

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
9 Reply
Re:VR400 Firmware Upgrade = No VDSL connection-Solution
2020-08-03 07:24:00 - last edited 2020-08-03 07:24:11

@jpuk

Hello!

After the firmware update, did you try to reset the modem and set up the internet connection type again?

And may I know what kind of connection type did you use for Plusnet, PPPOE? Do you also need Vlan ID?

If possible, can I have a picture of the DSL status page, such as:

 

Thank you very much~

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
Re:VR400 Firmware Upgrade = No VDSL connection
2020-08-03 20:34:47 - last edited 2020-08-03 20:39:55

  0  
  0  
#3
Options
Re:VR400 Firmware Upgrade = No VDSL connection
2020-08-03 20:40:20 - last edited 2020-08-03 20:55:50

I have done a full reset and setup from scratch. When I reinstall old firmware works instantly

 

  0  
  0  
#4
Options
Re:VR400 Firmware Upgrade = No VDSL connection
2020-08-04 00:19:52

@jpuk 

Good Day!

For your case, please also help us check the following information:

  1. What is your original firmware, is it Archer VR400(EU)_V2_170719 or Archer VR400(EU)_V2_200227?
  2. Since you did not mention VLAN ID, so I guess maybe Plusnet does not need that, so now, could you please try to do the same PPPoE Broadband connection on the computer to see if the computer would get internet, such as https://www.tp-link.com/support/faq/921/

(if the computer would be able to get internet, please try to clone the mac address on the VR400.)--it was under advanced--network--internet-modify(Or add);

Later, the related engineers would get in touch for further assistance.

Thank you~

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#5
Options
Re:VR400 Firmware Upgrade = No VDSL connection
2020-08-04 05:39:43

@Sunshine thanks for your assistance

Archer VR400(EU)_V2_170719 

​

This version works perfectly

 

Plusnet requires VLAN 101 which is set

  2  
  2  
#6
Options
Re:VR400 Firmware Upgrade = No VDSL connection
2020-11-20 07:46:31

@jpuk 

 

Did you ever get an answer to this, i have the same problem using the VR400 connecting to PLUSNET ADSL, DSL is connected but internet authentication never takes place.

 

Rolling back to previous firmware works.

 

Thanks,

Andrew 

  0  
  0  
#7
Options
Re:VR400 Firmware Upgrade = No VDSL connection
2020-11-20 08:15:55

@VR400V2 

 

Hello, thanks for bringing this up again.

 

Please kindly use the previous firmware, and we will soon release a new firmware, good day.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  1  
  1  
#8
Options
Re:VR400 Firmware Upgrade = No VDSL connection
2020-12-23 16:39:45

@Kevin_Z 

 

There is an updated firmware file available, no notes supplied as I don't use the tplink anymore so cannot test it but others following may do.

 

https://www.tp-link.com/uk/support/download/archer-vr400/v2/#Firmware

 

https://static.tp-link.com/2020/202012/20201223/Archer_VR400(EU)V2_201104.zip

 

 

 

Merry Christmas all.

  0  
  0  
#9
Options
Re:VR400 Firmware Upgrade = No VDSL connection
2020-12-24 02:46:34

@VR400V2 

 

Thank you again for sharing the info with the community. We do suggest our customer upgrade their device to the latest firmware if they encounter an issue.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#10
Options

Information

Helpful: 0

Views: 1678

Replies: 9

Related Articles
ADSL or VDSL @VR400
1061 0
vr400 v3 unstable VDSL connection
120 0
vr400 firmware
882 0
VR400 new firmware upgrade
630 1
confusion over VR400 v2 firmware upgrade
909 0
vr400 firmware upgrade 4503 error!!!??
664 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.