Help with remote access W8961N V3

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Help with remote access W8961N V3

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Help with remote access W8961N V3
Help with remote access W8961N V3
2020-08-07 14:47:44 - last edited 2020-08-10 01:07:14
Model: TD-W8961N  
Hardware Version: V3
Firmware Version:

Hello

 

Please I need your help guys with my home router, I have W8961N v3 

 

I set up ddns account in the management access section and I checked ACl by putting both interface lan and wan enabled.

 

When I try to connect to it on the same laptop that's connected to the router via browser by example.ddns.net it opens normally and everything is fine but when I try to use it in a different location like my workplace and type in the browser example.ddns.net it doesnt open at all.

 

Could you please guide me if I missed something here?

 

 

Thank you

  0      
  0      
#1
Options
3 Reply
Re:Help with remote access W8961N V3
2020-08-10 04:06:37 - last edited 2020-08-14 02:19:02

@Sinyas 

Good Day,

For your case, could you please check the following information:

  1. If the DDNS is not working, how about using the WAN IP address directly showing under the status page?
  2. When you try to ping the DDNS name, did it return with the same WAN IP address?
  3. And what kind of DDNS did you use?

Thank you~

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#2
Options
Re:Help with remote access W8961N V3
2020-08-10 15:32:04

@Sunshine 

 

Thank you for your time to reply sir

 

Im using noip services

 

When I log into my account on noip I find updated ip address same as my router which means ddns is working and communicates with the router prerfectly and if I try to use ddns address on the same computer linked to the router it opens normal no problem however on a different network it wont.

 

I dont know what ports are normally opened on the router by default so I can try to use if it works

 

 

Example :

 

Example.ddns.net:xxxx

 

I tried 80, 8080, 443 but nothing happens

 

P.S: plz note that on the same computer wired to the router it works without specifying any port just putting example.ddns.net in the browser it opens the config page of the router.

 

 

Thank you so much and have a good day

  0  
  0  
#3
Options
Re:Help with remote access W8961N V3
2020-08-14 02:25:44

@Sinyas 

Good day.

In this way, Did you try to use the WAN IP address to access the router from a different network as well?

And can I have a picture of your ACL setting for remote management?

May I know your current firmware about the TD-W8961N?

And how long have you had the router and is this the first time that you had this problem?

Thank you~

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 669

Replies: 3

Related Articles