No Gigabit on TL-PA7017P Kit AV1000
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.No Gigabit on TL-PA7017P Kit AV1000
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
I synced correctly TL-PA7017P and connected to the network, but I only reach 100mb out of 600mb I should.
What I am doing wrong?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Just to be clear, both my router and PC show I have Gigabit broadband so, no clue why I only receive 100 Mbps.
- Copy Link
- Report Inappropriate Content
@Acci Good day,
1. The real speed limited by the speed from main router. Please unplug the main powerline adapter, and wire a computer to the same Ethernet cable, what is the speed from main router? Please make sure that cable between router & the main powerline unit is a cat5E cable or above.
2. It is recommended to download the tpPLC Utility and check what is the powerline rate between 2 powerline units, if the speedtest results is about 20-30% of the powerline rate, it is reasonable. Here is a related FAQ that may help:
Explanation about the Powerline Rate and Actual speed of the Powerline Adapters
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
I am also in a similar situation as you are. From my part, I have a 200Mbps download speed on my ISP contract. But I still can not get the full desired speed but not even close to that. My powerline still spits out 100Mbps from my AV1000 dongles, with > Cat5E wired infrastructure.
From what I've seen on past posts, in my case, it might have to do with a Firmware issue.
- Copy Link
- Report Inappropriate Content
@JSilva Thank you for trying to help.
Speed will reduce when signal transmitted through power line, the actual speed could be different under different power line environment.
You may have a check the powerline rate between powerline adapter, the actual speed is around 20% -30% of the powerline rate and limited by the speed coming from router.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@Acci Hello,
There isn't a direct conversion rate between router speed and the speed of powerline unit. And the actual speed is closely related to the Powerline Rate which indicates the powerline environment in your house, if powerline environment is bad, more bandwidth will be lost during the transmission.
Here is part of my reply on #3 of your thread:
' It is recommended to download the tpPLC Utility and check what is the powerline rate between 2 powerline units, if the speedtest results is about 20-30% of the powerline rate, it is reasonable. Here is a related FAQ that may help:
Explanation about the Powerline Rate and Actual speed of the Powerline Adapters
- Copy Link
- Report Inappropriate Content
Hi, thanks for your answer, I understood what is explained both in your message and in the link you provide.
It seems that is assumed the user have to have this technical knowledge in advance and is not disclaimed anywhere.
Not fair.
- Copy Link
- Report Inappropriate Content
Hmm. I thought the data transfer inside the electrical current of the powerline speed just limited the data transfer from the Powerline adapter to the ethernet connected device in a direct way; more precisely that the global speed would be the Minimum of both speeds and not a percentage of the electrical current of the powerline speed.
- Copy Link
- Report Inappropriate Content
@JSilva Actually more data lose in the data travelling through house powerline between two PLC units, just like the speed loss in Air, speed also lose in powerline. Ethernet connection normally could preserve 80-90% of the data. For powerline connection, we could judge if actual speed in the normal range according to powerline rate. The conversion is 30% -40% when tested in the Lab, but the conversion could lower to around 20% to 30% in actual household environment.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 6477
Replies: 11
Voters 0
No one has voted for it yet.