Home Network Community > All Threads > Does the Archer MR400 work on the Telstra network
< All Threads

Does the Archer MR400 work on the Telstra network

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Does the Archer MR400 work on the Telstra network

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Does the Archer MR400 work on the Telstra network
Does the Archer MR400 work on the Telstra network
2021-06-09 09:11:20
Model: Archer MR400  
Hardware Version: V3
Firmware Version: V3_190226

Is the Archer MR400 compatible with the Telstra network?

 

When insert the SIM I get the message 

 

"Internet not connected. Internet unavailable due to no 3G or 4G signal. Please position the antennas upward and place the router in a location where it can get a good 3G or 4G signal reception."

 

It is not a signal issue as my mobile and a Nighthawk M2 have good signal strength. There is a fair amount of conflicting information on web regarding this.

  0      
 
  0      
 
#1
Options
2 Reply
Re:Does the Archer MR400 work on the Telstra network
2021-06-21 11:52:31

@MJD58 

 

Can we confirm what are the bands that the 4G base station provided by Telstra? MR400 supports the below:

4G: FDD-LTE B1/B3/B7/B8/B20 (2100/1800/2600/900/800 MHz)
TDD-LTE B38/B40/B41 (2600/2300/2500 MHz)
3G: DC-HSPA+/HSPA+/HSPA/UMTS B1/B8 (2100/900 MHz)

 

You can try to reset the MR400 by pressing and holding the RESET button until the LEDs flash off then on, check again if it can connect to the network when the Network Type is 4G preferred.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:Does the Archer MR400 work on the Telstra network
2021-06-21 22:51:59

@MJD58  I have discovered that 850MHz is the only 3G band that Telstra uses. Whilst the MR400 supports a number of 4G bands that Telstra uses, the 700MHz band is the one that has the longest range and best building penetration and is the primary band used outside of heavily built up areas. Neither of these bands is supported by the MR400. This means the MR400 really cannot be used by Telstra customers.

  0  
  0  
#3
Options

Information

Helpful: 0

Views: 1268

Replies: 2

Related Articles
Does the archer mr400 work on three network?
1243 0
Beta firmware for Archer MR400
3788 1
Archer MR400 disconnect from internet
23394 3
IPsec function not in Archer MR400
255 0
Setup up remote camera on the Archer MR400
708 0
SIM card not detecting in ARCHER MR400
1544 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.