Set up easymesh

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Set up easymesh

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Set up easymesh
Set up easymesh
2022-12-22 12:39:20 - last edited 2022-12-23 02:45:38
Model: Archer C80   RE700X  
Hardware Version:
Firmware Version:

How do you setup easymesh? I am planning to buy these routers + wifi extender. There will be one main router, a extender connected by ethernet and the other router upstairs connected by LAN -> WAN. How would I actually setup these routers? I can't find a easymesh guide anywhere.

  0      
  0      
#1
Options
1 Accepted Solution
Re:Set up easymesh-Solution
2022-12-22 18:01:46 - last edited 2023-01-10 12:27:35

  @Amogh_R 

 

Read through this thread - it includes a video guide for setting up and the device list that currently supports EasyMesh.

However, keep in mind that EasyMesh supports ethernet backhaul (ethernet cables between devices) on a few models through a beta FW so far.

You may consider a Deco system for this purpose as well - it's the only home grade mesh that supports ethernet backhaul so far.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
Recommended Solution
  3  
  3  
#2
Options
4 Reply
Re:Set up easymesh-Solution
2022-12-22 18:01:46 - last edited 2023-01-10 12:27:35

  @Amogh_R 

 

Read through this thread - it includes a video guide for setting up and the device list that currently supports EasyMesh.

However, keep in mind that EasyMesh supports ethernet backhaul (ethernet cables between devices) on a few models through a beta FW so far.

You may consider a Deco system for this purpose as well - it's the only home grade mesh that supports ethernet backhaul so far.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
Recommended Solution
  3  
  3  
#2
Options
Re:Set up easymesh
2022-12-22 21:05:42

 

terziyski wrote

  @Amogh_R 

 

Read through this thread - it includes a video guide for setting up and the device list that currently supports EasyMesh.

Although, keep in mind that Easy Mesh doesn't support ethernet backhaul (ethernet cables between devices) yet.

You may consider a Deco system for this purpose as well - it's the only home grade mesh that supports ethernet backhaul so far.

Thanks for the advice, I will be going with deco.

  0  
  0  
#3
Options
Re:Set up easymesh
2022-12-22 21:14:09
Just another point, does the deco s4 support than lan connection? I would much rather use lan over wireless. If not, can you tell me another relatively cheap model of deco that does?
  0  
  0  
#4
Options
Re:Set up easymesh
2022-12-22 22:29:16

  @Amogh_R 

 

Yes, they all do - that's their ethernet port could be used for.

See here how you can compare different Deco models.

Here's a guide on how to configure the Deco ethernet backhaul.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  2  
  2  
#5
Options

Information

Helpful: 0

Views: 1853

Replies: 4

Related Articles