Home

Forums

Stories

Knowledge Base

Home Network Community > All Threads > MR600 carrier aggregation not working

< All Threads

MR600 carrier aggregation not working

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

MR600 carrier aggregation not working

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

costof

2022-12-29 03:40:49 - last edited 2023-01-19 02:52:55

Posts: 3

Helpful: 1

Solutions: 1

Stories: 0

Registered: 2022-12-10

MR600 carrier aggregation not working

2022-12-29 03:40:49 - last edited 2023-01-19 02:52:55

Tags: #Carrier Aggregation #Band Selection

Model: Archer MR600

Hardware Version: V2

Firmware Version: 1.6.0 0.9.1 v0001.0 Build 220105 Rel.58321n

My MR600 v2 is not carrier aggregating the bands. I'm trying to aggregate bands 5 and 3 but it only connects to one at a time. 4g+ is abundantly and easily available in my location and anywhere in the house. The router is placed in a good position on the porch. I cannot see at 4g+ in any of the information displayed. The only reason I spent this premium amount on a router is for 4g+ and I'm not getting that.

File:

Screenshot (466).pngDownload

1 Accepted Solution

costof

LV1

2023-01-15 05:13:17 - last edited 2023-01-19 02:52:55

Posts: 3

Helpful: 1

Solutions: 1

Stories: 0

Registered: 2022-12-10

Re:MR600 carrier aggregation not working-Solution

2023-01-15 05:13:17 - last edited 2023-01-19 02:52:55

@Sunshine thank you for the reply. I'm getting 4g+ properly right now. After setting it up for the first time and getting 4g instantly, it takes a day to get 4g+ in a stable manner for some reason.

A warning or disclaimer in that regard would be better from tp-link for buyers as after paying a premium price just for a router and it not working accordingly tends to make it panicky

Recommended Solution

3 Reply

Sunshine

2023-01-08 04:43:20

Posts: 7375

Helpful: 1222

Solutions: 940

Stories: 0

Registered: 2018-12-17

Re:MR600 carrier aggregation not working

2023-01-08 04:43:20

@costof

Hi, please confirm if your SIM card supports to aggregate band 3+5 in your area or not, you could also insert the same SIM card into another 4G+ device or a smartphone, then check if it will work on 4G+, if so, please also check the bands information.

For smartphone, please refer to the instruction below to check the bands:

https://www.tp-link.com/en/support/faq/3488/

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.

costof

LV1

2023-01-15 05:13:17 - last edited 2023-01-19 02:52:55

Posts: 3

Helpful: 1

Solutions: 1

Stories: 0

Registered: 2022-12-10

Re:MR600 carrier aggregation not working-Solution

2023-01-15 05:13:17 - last edited 2023-01-19 02:52:55

@Sunshine thank you for the reply. I'm getting 4g+ properly right now. After setting it up for the first time and getting 4g instantly, it takes a day to get 4g+ in a stable manner for some reason.

A warning or disclaimer in that regard would be better from tp-link for buyers as after paying a premium price just for a router and it not working accordingly tends to make it panicky

Information

Helpful: 0

Replies: 3

MR600 carrier aggregation not working

MR600 carrier aggregation not working

Information

Voters 0

Tags