Home Network Community > All Threads > [TL-PA8030P KIT] AV1300 Powerline Adapter allows to connect only 1 device at a time
< All Threads

[TL-PA8030P KIT] AV1300 Powerline Adapter allows to connect only 1 device at a time

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

[TL-PA8030P KIT] AV1300 Powerline Adapter allows to connect only 1 device at a time

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
[TL-PA8030P KIT] AV1300 Powerline Adapter allows to connect only 1 device at a time
[TL-PA8030P KIT] AV1300 Powerline Adapter allows to connect only 1 device at a time
2023-03-25 18:13:34 - last edited 2023-03-30 01:03:36
Model: TL-PA8030P KIT  
Hardware Version: V3
Firmware Version: 2.7.0.44-02_803113_200117_901

AV1300 Powerline adapter provides internet connection only to the first device connected, devices that are connected after don't have internet connection. To have a device to connect to the internet trough the powerline adapter I need to unplug all other devices and plug only one device and only then it has connection to the internet. tpPLC shows the connected devices too.

Things I tried:

- Factory reset both powerline adapters

- Set DHCP auto on all devices

- Connected different devices, 2 desktops 2 routers. Same begavior on all devices.

- Switching source powerline adapter with node powerline adapter

- Tried different ports on powerline adapters

- Tried different Ethernet cables

 

Been picking my brains for what might be the culprit. Can't figure it out. Starting to think that I might have got defective powerline adapters

 

 

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:[TL-PA8030P KIT] AV1300 Powerline Adapter allows to connect only 1 device at a time-Solution
2023-03-29 12:07:37 - last edited 2023-03-30 01:03:36

  @Evaldas_B The source powerline adapter is connected through Ethernet cable to 5g modem. Any subsequently connected devices would not get internet connection.

The issue was caused by the modem itself, not the powerline adapters. The modem was in IP passtrough mode and so only single device would get public ip address provided by the ISP and local addresses were not given to connected devices. After putting the modem in router mode all the devices would get a local ip address and would connect to the internet.

TLDR: Check if the modem connected to your powerline adapter is not in IP passtrough mode

Recommended Solution
  0  
  0  
#3
Options
3 Reply
Re:[TL-PA8030P KIT] AV1300 Powerline Adapter allows to connect only 1 device at a time
2023-03-29 10:42:59

  @Evaldas_B 

 

Hi, may I know if the source powerline adapter is connected to a main router via Ethernet cable? and are you able to connect multiple devices to the main router directly?

If possible, please provide us with the whole network topology.

 

In addition, when you connect multiple client devices to the node powerline adapter, please check the IP address and default gateway on the first client device and another non-working client device for comparison. You could refer to the instruction here to find IP address etc. on client devices:

How to find IP address on your devices

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#2
Options
Re:[TL-PA8030P KIT] AV1300 Powerline Adapter allows to connect only 1 device at a time-Solution
2023-03-29 12:07:37 - last edited 2023-03-30 01:03:36

  @Evaldas_B The source powerline adapter is connected through Ethernet cable to 5g modem. Any subsequently connected devices would not get internet connection.

The issue was caused by the modem itself, not the powerline adapters. The modem was in IP passtrough mode and so only single device would get public ip address provided by the ISP and local addresses were not given to connected devices. After putting the modem in router mode all the devices would get a local ip address and would connect to the internet.

TLDR: Check if the modem connected to your powerline adapter is not in IP passtrough mode

Recommended Solution
  0  
  0  
#3
Options
Re:[TL-PA8030P KIT] AV1300 Powerline Adapter allows to connect only 1 device at a time
2023-03-30 01:03:26

  @Evaldas_B 

 

Hi, thanks a lot for the update, glad to hear that you've found and solved the problem!

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 820

Replies: 3

Related Articles
TL-PA8033P KIT (TL-PA8010P + 2 x TL-PA8030P) frequently disconnects
1837 0
TL-PA8030P KIT
779 0
TL-PA8030P Kit firmware Update Failed
1331 0
TL-PA8030P KIT mit WLAN Repeater erweiterbar???
336 0
TL-PA8030P KIT V2 and frequent disconnections problem
1467 0
TL-PA8030P (AV1200) slower than TL-PA4020P (AV500)
2353 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.