Home

Forums

Stories

Knowledge Base

Home Network Community > All Threads > Adding m% to XE75 Mesh but Ethernet wont work

< All Threads

Adding m% to XE75 Mesh but Ethernet wont work

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Adding m% to XE75 Mesh but Ethernet wont work

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

topgazza2

2024-05-15 12:08:57 - last edited 2024-05-16 08:41:40

Posts: 11

Helpful: 4

Solutions: 0

Stories: 0

Registered: 2024-04-20

Adding m% to XE75 Mesh but Ethernet wont work

2024-05-15 12:08:57 - last edited 2024-05-16 08:41:40

Model: Deco M5

Hardware Version: V1

Firmware Version:

Ive just installed and connected a Deco M5 to my Deco XE75 mesh.

Firmware update completed but plugging in a NAS via the ethernet port on the M5 doesnt result in a connection. So I did a factory reset and it asked me for a firmware update which I did. It then connected the NAS for about 10 seconds then dropped the ethernet connection. It now refuses to reconnect the NAS. Cables are OK

I was advised that an M5 is ideal for this situation. Using WIFI>Ethernet on devices with no WiFi. Is this doable ?

Any advice appreciated

1 Accepted Solution

David-TP

2024-05-16 03:30:27 - last edited 2024-05-16 08:41:40

Posts: 12847

Helpful: 1808

Solutions: 1298

Stories: 9

Registered: 2020-04-14

Re:Adding m% to XE75 Mesh but Ethernet wont work-Solution

2024-05-16 03:30:27 - last edited 2024-05-16 08:41:40

@topgazza2

Hi, Thanks for the feedback. The NAS should work when connecting via an Ethernet cable to the satellite M5.

Is NAS using DHCP to receive IP addresses?

There are 2 Ethernet ports on Deco M5 and did switching to another port make any difference?

By the way, are you able to temporarily connect the NAS to another satellite Deco XE75 to see whether the NAS could get an internet connection through the Ethernet cable?

Wait for your reply and best regards.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶KidShield Now Open for Trial! Try to leave a Message if urgent help is required.

Recommended Solution

2 Reply

David-TP

2024-05-16 03:30:27 - last edited 2024-05-16 08:41:40

Posts: 12847

Helpful: 1808

Solutions: 1298

Stories: 9

Registered: 2020-04-14

Re:Adding m% to XE75 Mesh but Ethernet wont work-Solution

2024-05-16 03:30:27 - last edited 2024-05-16 08:41:40

@topgazza2

Hi, Thanks for the feedback. The NAS should work when connecting via an Ethernet cable to the satellite M5.

Is NAS using DHCP to receive IP addresses?

There are 2 Ethernet ports on Deco M5 and did switching to another port make any difference?

By the way, are you able to temporarily connect the NAS to another satellite Deco XE75 to see whether the NAS could get an internet connection through the Ethernet cable?

Wait for your reply and best regards.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶KidShield Now Open for Trial! Try to leave a Message if urgent help is required.

Information

Helpful: 0

Replies: 2

Adding m% to XE75 Mesh but Ethernet wont work

Adding m% to XE75 Mesh but Ethernet wont work

Information

Voters 0

Tags