ER605 Router Bandwidth Control doesn't work as expected.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ER605 Router Bandwidth Control doesn't work as expected.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
ER605 Router Bandwidth Control doesn't work as expected.
ER605 Router Bandwidth Control doesn't work as expected.
2022-04-26 04:07:57 - last edited 2022-04-29 18:48:43
Model: ER605 (TL-R605)  
Hardware Version: V1
Firmware Version: 1.2.0

I use the ER605 Router configured with Hardware OC200.

 

Issue Description:

I have configured the Bandwidth Control Rule List as below with the respected IP Address. But, It limits the Bandwidth to whatever rule is at the top.

 

E.g.

I have a device with IP Address: 192.168.0.21, Which falls in the IP Group MAX.

I have Applied bandwidth control for Group MAX to 100Mbps, but my device gets limited to 30Mbps because the top rule (Office) gets applied to that device.

Observation:

So, what I found after a lot of combinations, is that whatever rule at the top gets applied to any client connected respective of the group it falls in.

Please find below screen shorts for more clarification.  

 

Note: Let me know If I am doing something wrong. Any help is appreciated.

 

Screenshots:

 

Bandwidth Control Rule:

Bandwidth Control Rule Details:

 

 

 

IP Group Details:

 

 

 

 

  3      
  3      
#1
Options
1 Accepted Solution
Re:ER605 Router Bandwidth Control doesn't work as expected.-Solution
2022-04-28 10:09:29 - last edited 2022-04-29 18:48:43

  @Pratz 

 

I suggest that you try changing the subnet mask to 32 when setting up the IP Group, 24 may contain too many IPs.

Just striving to develop myself while helping others.
Recommended Solution
  0  
  0  
#2
Options
4 Reply
Re:ER605 Router Bandwidth Control doesn't work as expected.-Solution
2022-04-28 10:09:29 - last edited 2022-04-29 18:48:43

  @Pratz 

 

I suggest that you try changing the subnet mask to 32 when setting up the IP Group, 24 may contain too many IPs.

Just striving to develop myself while helping others.
Recommended Solution
  0  
  0  
#2
Options
Re:ER605 Router Bandwidth Control doesn't work as expected.
2022-04-29 09:24:31

  @Virgo 

I hope the following can help you, and it works on my device.

The effective priority of bandwidth control rules is as follows: if a device IP belongs to multiple rules(IP Group or Network) at the same time, the rule which more near to the top of the bandwidth control rule list has better priority. If the device IP you are testing belongs to both Max and Office_PC, it is normal for the bandwidth to be limited to 30Mbps.
If you want the device bandwidth in Max to be limited to 100Mbps, try to long press and drag the rule on the page to make the rule of IP Group Max at the top of the bandwidth control rule list.

  0  
  0  
#3
Options
Re:ER605 Router Bandwidth Control doesn't work as expected.
2022-04-29 18:50:28

  @Virgo I am not sure how that worked, but it did. Thank you so much. Can you please explain to me why that worked?

  0  
  0  
#4
Options
Re:ER605 Router Bandwidth Control doesn't work as expected.
2022-05-03 12:11:36

  @Pratz 

 

If you change it to 32 then it only refers to this one IP address alone.
But you set it to 24 then it means that the subnet mask is 255.255.255.0, which contains a lot of IPs.

Just striving to develop myself while helping others.
  1  
  1  
#5
Options