Business Community > Controllers > 4 WAN LOAD BALANCING RATIO(ER8411)
< Controllers

4 WAN LOAD BALANCING RATIO(ER8411)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

4 WAN LOAD BALANCING RATIO(ER8411)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
4 WAN LOAD BALANCING RATIO(ER8411)
4 WAN LOAD BALANCING RATIO(ER8411)
2024-03-17 14:34:46 - last edited 2024-03-18 02:15:22
Model: OC200   ER8411  
Hardware Version: V1
Firmware Version:

I am step 4 WAN load balance but loads are not merged can't understand how to configure the WAN Ratio

 

WAN1 speed 300 Mbps, WAN2 speed 500 Mbps, WAN3 speed 250Mbps, WAN4 Speed 500 Mbps

 

Kindly Suggest the ratio

 

 

Omada & VIGI | Using at 3 Locations | Controller: V6.0.0.19 (Linux) | GW: ER7206 | SW: SG2428P & SG2210P | APs: 2 × EAP610 | WAN: Jio&Airtel | NVR2016H & 8 Cam's.
  0      
 
  0      
 
#1
Options
2 Accepted Solutions
Re:4 WAN LOAD BALANCING RATIO(ER8411)-Solution
2024-03-17 18:35:19 - last edited 2024-03-18 02:15:26

  @Babun-Sikder 

 

When you mentioned "merge" that is technically "wan bonding"  That is completely different from Load Balancing.

 

Bonding is merging all WAN ports as 1 WAN port... only high-end routers do this... nothing you and I can afford.  PepLink does a Semi Bonding config.  

 

But Load Balancing... you set up the weight of which WAN you want to go 1st, 2nd, 3rd, and 4th.  

 

 

I can not teach anyone anything - I can only make them think - Socrates
Recommended Solution
  1  
  1  
#2
Options
Re:4 WAN LOAD BALANCING RATIO(ER8411)-Solution
2024-03-18 02:15:15 - last edited 2024-03-18 02:15:22

Hi @Babun-Sikder 

Thanks for posting in our business forum.

Please take a look at this guide in explaining load balancing bonding or merging speed.

Recommended Solution
  3  
  3  
#3
Options
2 Reply
Re:4 WAN LOAD BALANCING RATIO(ER8411)-Solution
2024-03-17 18:35:19 - last edited 2024-03-18 02:15:26

  @Babun-Sikder 

 

When you mentioned "merge" that is technically "wan bonding"  That is completely different from Load Balancing.

 

Bonding is merging all WAN ports as 1 WAN port... only high-end routers do this... nothing you and I can afford.  PepLink does a Semi Bonding config.  

 

But Load Balancing... you set up the weight of which WAN you want to go 1st, 2nd, 3rd, and 4th.  

 

 

I can not teach anyone anything - I can only make them think - Socrates
Recommended Solution
  1  
  1  
#2
Options
Re:4 WAN LOAD BALANCING RATIO(ER8411)-Solution
2024-03-18 02:15:15 - last edited 2024-03-18 02:15:22

Hi @Babun-Sikder 

Thanks for posting in our business forum.

Please take a look at this guide in explaining load balancing bonding or merging speed.

Recommended Solution
  3  
  3  
#3
Options

Information

Helpful: 0

Views: 1040

Replies: 2

About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.