Business Community > Controllers > Omada VLAN DHCP Relay Configuration
< Controllers

Omada VLAN DHCP Relay Configuration

Omada VLAN DHCP Relay Configuration

Omada VLAN DHCP Relay Configuration
Omada VLAN DHCP Relay Configuration
Monday - last edited Yesterday
Tags: #VLAN & Multi-Networks #Controller
Model: OC200  
Hardware Version: V5
Firmware Version: 1.31.3 Build 20240620 Rel.80383

Hi Team,

I currently have the following equipment which I recently purchased to replace my Ubiquiti setup:

 

1 x OC200 (Controller version 5.14.26.23) 
1 x TP-Link ER7206 v2.20 (Version 2.2.2)
3 x SG2210MP v5.0 (Version 5.0.12)
1 x SG2428P v5.30 (Version 5.30.13)
1 x EAP610-Outdoor(EU) v1.0 (Version 1.4.3)
3 x EAP653(EU) v1.0 (Version 1.1.3)

 

I have a DHCP server running on Windows where I have configured 15 different scopes which were serving the 15 different VLANS I have across my network in the Ubiquiti setup.

 

I have followed the online TP-Link guides but am still struggling to get the DHCP Relay for the VLANS to function at all.

 

Any pointers please?

 

Thanks

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Omada VLAN DHCP Relay Configuration-Solution
Yesterday - last edited Yesterday

@GRL  This is exactly what DHCP Relay is made for and does support VLAN's.

 

@Turbotim2025 Have a look at this guide, chapter 1.2 "In controller mode". You may have already seen this or not, but it explains (in not too much detail unfortunately) what you have to do. You will probably have to search for a few options since the interface has changed a bit as of controller version 6.

I do not know what your network setup looks like, but it is possible that the VLAN's are not enabled/distributed properly across the switches or the switch interconnecting ports are not setup as trunks with multiple VLAN's. Perhaps a quick sketch of your setup can help us to narrow it down.

 

ER707-M2, SG3218XP-M2, EAP772's & EAP245's
Recommended Solution
  0  
  0  
#5
Options
6 Reply
Re:Omada VLAN DHCP Relay Configuration
Yesterday

  @Turbotim2025 

 

Why use a windows server for DHCP on a relatively small network?  just use the gateway DHCP

  0  
  0  
#2
Options
Re:Omada VLAN DHCP Relay Configuration
Yesterday

  @GRL 

just because I prefer to.

 

  0  
  0  
#3
Options
Re:Omada VLAN DHCP Relay Configuration
Yesterday

  @Turbotim2025 

 

You would need to make your windows system aware of all vlans and it have a tagged interface on all vlans you want it to serve DHCP on

I dont think omada DHCP relay can function cross-vlan boundaries

  0  
  0  
#4
Options
Re:Omada VLAN DHCP Relay Configuration-Solution
Yesterday - last edited Yesterday

@GRL  This is exactly what DHCP Relay is made for and does support VLAN's.

 

@Turbotim2025 Have a look at this guide, chapter 1.2 "In controller mode". You may have already seen this or not, but it explains (in not too much detail unfortunately) what you have to do. You will probably have to search for a few options since the interface has changed a bit as of controller version 6.

I do not know what your network setup looks like, but it is possible that the VLAN's are not enabled/distributed properly across the switches or the switch interconnecting ports are not setup as trunks with multiple VLAN's. Perhaps a quick sketch of your setup can help us to narrow it down.

 

ER707-M2, SG3218XP-M2, EAP772's & EAP245's
Recommended Solution
  0  
  0  
#5
Options
Re:Omada VLAN DHCP Relay Configuration
Yesterday

  @Theedoek 

 

Thank you very much for your assistance, I went through that guide and got DHCP Relay from my Windows Server to the VLANS functioning correctly.

  0  
  0  
#6
Options
Re:Omada VLAN DHCP Relay Configuration
Yesterday

  @Turbotim2025 that is good news. Glad I could help.

ER707-M2, SG3218XP-M2, EAP772's & EAP245's
  0  
  0  
#7
Options

Information

Helpful: 0

Views: 71

Replies: 6

Tags

VLAN & Multi-Networks Controller
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.