Business Community > Gateways > 470T+ configuration
< Gateways

470T+ configuration

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

470T+ configuration

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
470T+ configuration
470T+ configuration
2018-09-16 08:26:18 - last edited 2021-04-20 11:25:26

I have two Boradband connection they come with their own modem and it is not possible to connect the cable to wan port directly.

DSL1 router IP ( Broad band with Dynamic IP assignment )- 192.168.1.22/24

DSL 2 ( VDSL) router IP - 192.168.1.33/24

 

is it possible to use the 470T+ to load balance connection with the same LAN segment or use the device to failover to the second DSL when primary is not available.

 

any help in this regard will be appreciated.

 

regards,

Vikas

 

  0      
 
  0      
 
#1
Options
3 Reply
Re:470T+ configuration
2018-09-17 06:24:25 - last edited 2021-04-20 11:25:26

vkhandelwal wrote

I have two Boradband connection they come with their own modem and it is not possible to connect the cable to wan port directly.

DSL1 router IP ( Broad band with Dynamic IP assignment )- 192.168.1.22/24

DSL 2 ( VDSL) router IP - 192.168.1.33/24

 

is it possible to use the 470T+ to load balance connection with the same LAN segment or use the device to failover to the second DSL when primary is not available.

 

any help in this regard will be appreciated.

 

regards,

Vikas

 

 

Hi Sir

 

I think what you want is the Link Backup function.

You can refer to the FAQ: https://www.tp-link.com/en/faq-2133.html

 

 

Deco Monthly Recap- Check What's Currently Going on With Deco KidShield Test Recruitment, Share Your Ideas With us! Wi-Fi Schedule Ideas Wanted!
  0  
  0  
#2
Options
Re:470T+ configuration
2018-09-17 10:23:37 - last edited 2021-04-20 11:25:26

vkhandelwal wrote

I have two Boradband connection they come with their own modem and it is not possible to connect the cable to wan port directly.

DSL1 router IP ( Broad band with Dynamic IP assignment )- 192.168.1.22/24

DSL 2 ( VDSL) router IP - 192.168.1.33/24

 

is it possible to use the 470T+ to load balance connection with the same LAN segment or use the device to failover to the second DSL when primary is not available.

 

any help in this regard will be appreciated.

 

regards,

Vikas

 

Well, I have only tl-er6120v2, so I checked there and there is no error, when you configure IPs from the same subnetwork on 2 WANs with enabled Load Balance. I do not know, how routing will work though... Link Backup should work with no problem then, while I am not sure about Load Balance. So, if you have the latest hw version of TL-R470T+ (new WebGui as in TL-ER6120v2/v3), it will probably work.

  1  
  1  
#3
Options
Re:Re:470T+ configuration
2018-09-29 04:51:41 - last edited 2021-04-20 11:25:26

I cannot set the IP address of wan port from same network as LAN port. that is the erro i get while setting up a ip address of WAN port

  0  
  0  
#4
Options

Information

Helpful: 0

Views: 1194

Replies: 3

About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.