OC200: After Firmware update to 4.2.8 issues with client list

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

OC200: After Firmware update to 4.2.8 issues with client list

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
OC200: After Firmware update to 4.2.8 issues with client list
OC200: After Firmware update to 4.2.8 issues with client list
2020-12-31 15:45:22 - last edited 2020-12-31 16:04:10
Model: OC200  
Hardware Version: V1
Firmware Version: 4.2.8

Hi,

 

I updated my OC200 to the new firmware 4.2.8 this morning.

Other devices in my network are

 

1 x TL-R605

1 x T1500G-8T

3 x EAP245

 

All running latest firmware.

 

SInce the update, the client list in the Dashboard is acting strange. I have about 18 clients. 9 are wired, the others are wireless.

The client list is refreshing from time to time (as expected), but many times, the wireless clients get listed as wired.

I then see 0 wireless and 18 wired clients.

 

This obviously makes the controller quite useless in terms of monitoring.

 

This issue was not observed with the 4.2.4 firmware.

 

Am I the only one seeing this?

 

Thanks,

  Marc

  0      
  0      
#1
Options
6 Reply
Re:OC200: After Firmware update to 4.2.8 issues with client list
2021-01-03 12:49:57

@MacRue 

 

Good Morning

 

I had the same issue when i updated, namely that wireless devices where appearing as wired..   upon checking they all appeared on the same port as the WiFi AP (EAP245)

 

This appears to have resolved itself following a 2nd reboot and some time passing, been around 4 days now with no more instances of this

 

Hopefully the same for you

  0  
  0  
#4
Options
Re:OC200: After Firmware update to 4.2.8 issues with client list
2021-01-12 10:43:49

Dear @MacRue,

 

Are your EAP245s connected to the T1500G-8T via Ethernet cable, and is your T1500G-8T managed by the OC200?

 

As Philbert mentioned, would it help for your case if you reboot the OC200 twice?

2022 TP-Link Wi-Fi 7 Product Launch Event | Watch the Replay at https://www.tp-link.com/us/wifi7/event/.
  0  
  0  
#5
Options
Re:OC200: After Firmware update to 4.2.8 issues with client list
2021-01-13 02:30:32

Hi All,

 

For the problem that the wireless clients show as wired in Omada SDN controller, I've updated the result in this post.

2022 TP-Link Wi-Fi 7 Product Launch Event | Watch the Replay at https://www.tp-link.com/us/wifi7/event/.
  0  
  0  
#8
Options
Re:OC200: After Firmware update to 4.2.8 issues with client list
2021-01-13 14:21:26

@Fae ,

 

thanks a lot for the update. Good to know, engineering has already identified the issue.

 

Best,

  Marc

  0  
  0  
#9
Options
Re:OC200: After Firmware update to 4.2.8 issues with client list
2021-01-13 14:27:28

@Fae 

 

just for completeness:

 

Fae wrote

Dear @MacRue,

 

Are your EAP245s connected to the T1500G-8T via Ethernet cable, and is your T1500G-8T managed by the OC200?

 

As Philbert mentioned, would it help for your case if you reboot the OC200 twice?

 

One EAP245 is wire connected to the T1500G-8T, the other wired to the TL-R605 - Both are managed by the OC200 and reboots did not change the situation.

 

Regards,

  Marc

  0  
  0  
#10
Options
Re:OC200: After Firmware update to 4.2.8 issues with client list
2022-01-10 09:51:43

 

I have the Same Problem yesterday after the update in the OC 200 No Device found.

 

See then 4 times the EPA245 Wired and one switch  TL-SG3428MP. I find them in the Omada Cloud but with the message behind the epa or switch MANAGED BY OTHERS. 

The problem is i don't can addpt APE or switch ( He aks for Username and Pass wort change bie OC200) .

 

How i can adopt again the APE or switch.

 

Thanks for your help. 

  0  
  0  
#11
Options