Business Community > Routers > Dual WAN port forwarding stopped working reliably with v2.1.1
< Routers

Dual WAN port forwarding stopped working reliably with v2.1.1

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Dual WAN port forwarding stopped working reliably with v2.1.1

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Dual WAN port forwarding stopped working reliably with v2.1.1
Dual WAN port forwarding stopped working reliably with v2.1.1
2023-02-07 12:35:12 - last edited 2023-02-07 12:41:28
Tags: #VLAN & Multi-Networks #NAT #WAN Setup
Model: ER605 (TL-R605)  
Hardware Version: V2
Firmware Version: v2.1.1

My OC200 auto-updated my ER605 (v2 h/w) from v2.0.x to v2.1.1 a couple of days ago and since then my inbound NATs have stopped working reliably. I have "WAN" on a VDSL connection with a single static IP and "WAN1" connected to Starlink. Both have IPv4 and IPv6 enabled. "WAN" allows inbound connections on a range of TCP ports for things like small websites, home automation dashboards and also Plex and LMS Squeezeserver.

 

I have power cycled the ER605 to ensure it's not anything like leaking state tables and the like, but still no luck.

 

I am going to probably revert manually back to v2.0.1 but before I do, any ideas folks?

  0      
 
  0      
 
#1
Options
5 Reply
Re:Dual WAN port forwarding stopped working reliably with v2.1.1
2023-02-08 06:31:41

I downgraded to 2.0.1 this morning while no one was using the ;'net and it has fully recovered and the old, correct, behavior is back.

 

I re-read the release notes and nothing obvious jumps out about new settings or configs to make symmetric routing work for inbound NAT port forwards.

  0  
  0  
#2
Options
Re:Dual WAN port forwarding stopped working reliably with v2.1.1
2023-02-08 07:53:02

 Dear @pgalbavy 

 

Thank you for your kindly feedback. I will report this issue to our R&D department. 

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  1  
  1  
#3
Options
Re:Dual WAN port forwarding stopped working reliably with v2.1.1
2023-02-08 08:25:31

  @Hank21 Thanks. Happy to share configs and details as required to reproduce the issue.

  0  
  0  
#4
Options
Re:Dual WAN port forwarding stopped working reliably with v2.1.1
2023-02-08 08:49:07

Dear  @pgalbavy 

 

To better assist you, I've created a support ticket via your registered email address, and escalated it to our support engineer to look into the issue. 

The ticket ID is TKID230213532, please check your email box and ensure the support email is well received. Thanks!

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#5
Options
Re:Dual WAN port forwarding stopped working reliably with v2.1.1
2023-02-08 09:04:31
Got it, and actioning the config upload - thanks!
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 280

Replies: 5

Tags

VLAN & Multi-Networks NAT WAN Setup
About Us
Press
Copyright © TP-LINK CORPORATION PTE. LTD. All rights reserved.