EAP Beta Firmware for Omada SDN Controller v5.9 (Updated on May 6th, 2024)- [Thread Closed]

EAP Beta Firmware for Omada SDN Controller v5.9 (Updated on May 6th, 2024)- [Thread Closed]

275 Reply
Re:EAP Beta Firmware for Omada SDN Controller v5.9 (Updated on Aug 7th, 2023)
2023-09-06 03:22:03

Hello @jg1212,

 

jg1212 wrote

@Fae I ended up returning my new EAP670 because of this. After a while 4 of my devices in the 2.4 range would not receive IP addresses. They show connected but no IP. The Logs showed that they were being blocked by ACL rules which didn't exist. I tried upgrading to 1.0.11 but it didn't help. I could not downgrade to 1.0.6 because the EAP670 shipped with something between 1.0.6 and 1.0.11 which isn't available to download. The AP refused 1.0.6. I replaced it with an EAP610 and all is working perfectly again. Something very wrong with the EAP670. Just wanted you to know it is not just you. Thanks, JG

 

When you find the "Blocked by ACL" logs at Insights > Past Connection > Association Failure, it may cause by the following feature:

  • ACL
  • MAC Filter
  • Lock to AP

 

If the issue starts after you upgrade to 1.0.11 firmware, it's recommended to check whether you have configured the Lock to AP feature on your 4 devices in question.

 

Go to Insights > Known Clients or Past Connections, find your devices in question and highlight it to open its properties window, go to Config to check whether the Lock to AP feature is enabled. If it is, please disable the Lock to AP feature and Save the settings, then check whether it works.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#105
Options
Re:EAP Beta Firmware for Omada SDN Controller v5.9 (Updated on Aug 31st, 2023)
2023-09-06 03:30:36 - last edited 2023-09-06 03:30:52

Hello @jg1212,

 

jg1212 wrote

 @Fae 

One of my EAP610 V2 APs was received with firmware 1.1.1.  I tryied updating it to Beta 1.1.3 but it keeps failing saying that the upgrade file is invalid.  Do you know what the issue could be? My other two APs upgraded from 1.0.2 to 1.1.3 just fine.

 

May I know where you got the 1.1.1 firmware from? Do you still have the firmware download link?

And could you please provide the firmware Build number of your 1.1.1 firmware?

 

How to get the firmware Build number:

In Devices list, highlight the EAP610 V2 with 1.1.1 firmware, then find the full Build number at Details > Overview from its properties window.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#106
Options
Re:EAP Beta Firmware for Omada SDN Controller v5.9 (Updated on Aug 31st, 2023)
2023-09-06 03:36:59

Hello @bitjump,

 

bitjump wrote

We upgraded the EAP670 to 1.0.11 and noticed that we are unable to negotiate to 2.5G. We even tried using a 2' CAT7 patch cable connected directly to the Netgear switch (MS108EUP). Other devices on the network have no issues negotiating to 2.5G to the same switch.

 

Please let me know if there are any other test cases. We own three of these devices and all three behave the same way.

 

What's the previous firmware version of the EAP670? Are you able to negotiate to 2.5G before you upgrade to 1.0.11 firmware?

 

If you are using a PoE switch to power up the EAP670, you may replace with the original 12 V / 1.5 A DC power adapter for tests.

Besides, if possible, please check if the EAP670 can negotiate to 2.5G with other 2.5G devices.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#107
Options
Re:EAP Beta Firmware for Omada SDN Controller v5.9 (Updated on Aug 7th, 2023)
2023-09-06 12:39:14

Fae wrote

Hello @jg1212,

 

jg1212 wrote

@Fae I ended up returning my new EAP670 because of this. After a while 4 of my devices in the 2.4 range would not receive IP addresses. They show connected but no IP. The Logs showed that they were being blocked by ACL rules which didn't exist. I tried upgrading to 1.0.11 but it didn't help. I could not downgrade to 1.0.6 because the EAP670 shipped with something between 1.0.6 and 1.0.11 which isn't available to download. The AP refused 1.0.6. I replaced it with an EAP610 and all is working perfectly again. Something very wrong with the EAP670. Just wanted you to know it is not just you. Thanks, JG

 

When you find the "Blocked by ACL" logs at Insights > Past Connection > Association Failure, it may cause by the following feature:

  • ACL
  • MAC Filter
  • Lock to AP

 

If the issue starts after you upgrade to 1.0.11 firmware, it's recommended to check whether you have configured the Lock to AP feature on your 4 devices in question.

 

Go to Insights > Known Clients or Past Connections, find your devices in question and highlight it to open its properties window, go to Config to check whether the Lock to AP feature is enabled. If it is, please disable the Lock to AP feature and Save the settings, then check whether it works.

  @Fae 

I checked all of those places and NONE of them had any data.  I had previously used "Lock to AP" but removed it once the issues started.  Unfortunately I can not do any further testing on this since I already returned the 670 and replaced it with a 610 which is working perfectly.

Thanks,

JG

  0  
  0  
#108
Options
Re:EAP Beta Firmware for Omada SDN Controller v5.9 (Updated on Aug 31st, 2023)
2023-09-06 12:42:34

Fae wrote

Hello @jg1212,

 

jg1212 wrote

 @Fae 

One of my EAP610 V2 APs was received with firmware 1.1.1.  I tryied updating it to Beta 1.1.3 but it keeps failing saying that the upgrade file is invalid.  Do you know what the issue could be? My other two APs upgraded from 1.0.2 to 1.1.3 just fine.

 

May I know where you got the 1.1.1 firmware from? Do you still have the firmware download link?

And could you please provide the firmware Build number of your 1.1.1 firmware?

 

How to get the firmware Build number:

In Devices list, highlight the EAP610 V2 with 1.1.1 firmware, then find the full Build number at Details > Overview from its properties window.

  @Fae 

The EAP610 came from Amazon with this firmware a couple days ago.  

Here is the full model and firmware build:

Model:   EAP610(US) v2.0

Firmware Version:   1.1.1 Build 20230524 Rel. 74262

  0  
  0  
#109
Options
Re:EAP Beta Firmware for Omada SDN Controller v5.9 (Updated on Aug 2nd, 2023)
2023-09-06 14:47:15 - last edited 2023-09-06 16:39:43

@Fae Is it right when I lock a client to a specific ap and it will connect to a another ap I ve got the message blocked ?

 

so yes can I turn off that messages or can I solve it ? 

  0  
  0  
#110
Options
Re:EAP Beta Firmware for Omada SDN Controller v5.9 (Updated on Aug 31st, 2023)
2023-09-07 01:26:29

i tried updating my three EAP610 v2 to the 1.1.2 builds last week and one of my access points was no longer accepting connections. devices were unable to connect to it so i rolled back to 1.0.2 on all three devices. has anyone been running 1.1.3 on their EAP610 v2 and not had any issues yet? i was hoping 1.1.3 resolved whatever issue was going on so i can use the Lock to AP feature.

  0  
  0  
#111
Options
Re:EAP Beta Firmware for Omada SDN Controller v5.9 (Updated on Aug 31st, 2023)
2023-09-07 01:32:18

  @dictoresno 

dictoresno wrote

i tried updating my three EAP610 v2 to the 1.1.2 builds last week and one of my access points was no longer accepting connections. devices were unable to connect to it so i rolled back to 1.0.2 on all three devices. has anyone been running 1.1.3 on their EAP610 v2 and not had any issues yet? i was hoping 1.1.3 resolved whatever issue was going on so i can use the Lock to AP feature.

i'm on 1.1.3 and have no issues. Everything is running great. 
JG

  1  
  1  
#112
Options
Re:EAP Beta Firmware for Omada SDN Controller v5.9 (Updated on Aug 31st, 2023)
2023-09-07 01:47:29 - last edited 2023-09-07 02:15:17

  @jg1212 

 

i updated one of my access points to 1.1.3 and even though theres a device in the same room with it and its set up to lock to that AP, it refuses to connect to it. this is the same issue i was having before. it appears to be favoring the one AP i didnt update of the three. do all the AP's on the network need to be lock capable for them to work right?

  0  
  0  
#113
Options
Re:EAP Beta Firmware for Omada SDN Controller v5.9 (Updated on Aug 31st, 2023)
2023-09-07 02:18:55

  @dictoresno 

i believe they all need to be updated. . 

  0  
  0  
#114
Options