EAP655-WALL_V1_1.2.0_Build 20230717 (Beta)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

EAP655-WALL_V1_1.2.0_Build 20230717 (Beta)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
EAP655-WALL_V1_1.2.0_Build 20230717 (Beta)
EAP655-WALL_V1_1.2.0_Build 20230717 (Beta)
2023-08-09 15:10:21 - last edited 2023-08-10 09:53:29
Model: EAP655-Wall  
Hardware Version: V1
Firmware Version: 1.0.2

Does this Beta firmware resolved the issue of VLAN tags not being handled correctly on another access point particularly EAP225-Outdoor Hardware Version 3.0 connected on Ethernet 3 (PoE enabled)?

 

All SSIDs we are using are assigned with different VLAN IDs. VLANs are handled correctly on EAP655-Wall but not on EAP225-Otdoor.

  0      
  0      
#1
Options
1 Accepted Solution
Re:EAP655-WALL_V1_1.2.0_Build 20230717 (Beta)-Solution
2023-08-10 09:53:23 - last edited 2023-08-10 09:53:29

Hello @CarloPH,

 

After confirming with the Support Engineer, the VLAN Bug fixed hasn't been added in this 1.2.0 Beta firmware, I have reported it to them for attention.

It will be added in the further software iterations, thanks for your valuable feedback.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  1  
  1  
#4
Options
4 Reply
Re:EAP655-WALL_V1_1.2.0_Build 20230717 (Beta)
2023-08-09 15:45:22

  @CarloPH 

 

I have had zero issues with multiple VLANs (one per SSID) running on EAP225-outdoorunits since firmware version 5.0.5 (currently I'm on 5.0.9).  Suspect the issue is more the configuration of the ethernet switch port to which the EAP225 is connected perhaps?

<< Paying it forward, one juicy problem at a time... >>
  2  
  2  
#2
Options
Re:EAP655-WALL_V1_1.2.0_Build 20230717 (Beta)
2023-08-09 22:50:46

  @d0ugmac1, I'm sorry if I've been vague in stating my problem. I also failed to mention that this is under Omada Controller and here is how it is connected:

 

Router > PoE Switch > EAP655-Wall (Ethe3 PoE enabled) > EAP225-Outdoor

 

No issues on VLANs when both EAP are plugged directly on the Trunk Ports of PoE Switch. However when EAP225-Outdoor is cascaded from the Eth3 of EAP655-Wall it cannot get an IP address on SSIDs with VLAN tags. There is a known issue about this here...

 

https://community.tp-link.com/en/business/forum/topic/605508

 

But the firmware version there is lower than the preloaded firmware of the EAP655-Wall (1.0.0-Beta versus 1.0.2). This is the reason why I was hoping this 1.2.0 Beta version also resolves the VLAN tagging issue.

 

d0ugmac1 wrote

  @CarloPH 

 

I have had zero issues with multiple VLANs (one per SSID) running on EAP225-outdoorunits since firmware version 5.0.5 (currently I'm on 5.0.9).  Suspect the issue is more the configuration of the ethernet switch port to which the EAP225 is connected perhaps?

 

  0  
  0  
#3
Options
Re:EAP655-WALL_V1_1.2.0_Build 20230717 (Beta)-Solution
2023-08-10 09:53:23 - last edited 2023-08-10 09:53:29

Hello @CarloPH,

 

After confirming with the Support Engineer, the VLAN Bug fixed hasn't been added in this 1.2.0 Beta firmware, I have reported it to them for attention.

It will be added in the further software iterations, thanks for your valuable feedback.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  1  
  1  
#4
Options
Re:EAP655-WALL_V1_1.2.0_Build 20230717 (Beta)
2023-08-10 12:42:47

  @Hank21, Thanks for the info.

 

Btw, I've tried the Beta Version 1.0.0 and it does fixed the VLAN tagging issues.

  2  
  2  
#5
Options

Information

Helpful: 0

Views: 378

Replies: 4

Related Articles