Business Community > WiFi > Access Point Disconnects After Power Outages
< WiFi

Access Point Disconnects After Power Outages

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Access Point Disconnects After Power Outages

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Access Point Disconnects After Power Outages
Access Point Disconnects After Power Outages
2023-11-17 13:22:31 - last edited 2023-12-04 11:29:52
Tags: #Mesh #Network Connectivity
Model: EAP610  
Hardware Version: V3
Firmware Version: 1.3.2 Build 20230414

I am seeking assistance to address a persistent issue related to my Access Points in a complex network scenario. Here is the setup:

 

  • A router from the service provider connected to the WAN port of an ER605 router.
  • A TL-SG2210MP switch.
  • Seven EAP610 Access Points, with three connected via POE to the TL-SG2210MP and the others through MESH.

 

The complication arises when there is a power outage. All EAP610s not connected via POE are disconnected and require a physical reset. This situation becomes problematic, especially because physical access during these interruptions is challenging.

 

My questions:

  1. Is there a solution to prevent the disconnection of EAP610s not connected via POE during power outages?
  2. Are there specific settings that can be adjusted to better handle this issue?
     

 

  0      
 
  0      
 
#1
Options
2 Accepted Solutions
Re:Access Point Disconnects After Power Outages-Solution
2023-11-20 06:10:01 - last edited 2023-12-04 11:29:52

  @danielpedrosaa 

 

Did you enable Auto failover?

 

 

There is a new beta firmware you can give it a shot if you want.

Just striving to develop myself while helping others.
Recommended Solution
  0  
  0  
#2
Options
Re:Access Point Disconnects After Power Outages-Solution
2023-12-04 11:29:32 - last edited 2023-12-05 05:40:35

Following @Virgo recommendation, I upgraded the firmware on two EAPs while keeping one without the update. After conducting thorough tests, I found that the firmware upgrade effectively resolved my issue.

Recommended Solution
  2  
  2  
#8
Options
8 Reply
Re:Access Point Disconnects After Power Outages-Solution
2023-11-20 06:10:01 - last edited 2023-12-04 11:29:52

  @danielpedrosaa 

 

Did you enable Auto failover?

 

 

There is a new beta firmware you can give it a shot if you want.

Just striving to develop myself while helping others.
Recommended Solution
  0  
  0  
#2
Options
Re:Access Point Disconnects After Power Outages
2023-11-21 13:42:48

  @Virgem 

Yes, Auto Failover is enabled! I have reactivated it, but the issue persists.

  0  
  0  
#3
Options
Re:Access Point Disconnects After Power Outages
2023-11-22 01:56:39

  @danielpedrosaa 

 

Is it possible that the mesh AP and root AP are a bit far apart and what is the signal strength of the mesh AP? 
Generally speaking, mesh AP needs to wait for some time to connect to the root AP after powering up, observe for some time to see if it will reconnect.
If you just re-adopt mesh AP, can' it solve the problem? Do you have to reset?

Just striving to develop myself while helping others.
  0  
  0  
#4
Options
Re:Access Point Disconnects After Power Outages
2023-11-22 03:47:32

  @danielpedrosaa 

 

How are you powering the meshed units?  Please make sure that there is no valid ethernet link present on the meshed AP port (ie don't use a cheap POE switch to power these units, instead use POE injectors or if you must use a POE switch, then break the etherlink by chopping out a datapair on the cable (ie disconnect pins 1 & 2).  It seems counterintuitive but meshed APs come back online a lot quicker if they cannot find an active wired link.

 

This should maybe be a feature request for mesh capable APs.  Add aconfig option to Prefer Mesh or Prefer Wired on restart.

<< Paying it forward, one juicy problem at a time... >>
  2  
  2  
#5
Options
Re:Access Point Disconnects After Power Outages
2023-11-23 02:20:23

  @danielpedrosaa 

 

Another suggestion, maybe the channel has changed caused the mesh AP can not reconnect. Tried put the root AP fixed on the Band1/Band4.

Just striving to develop myself while helping others.
  0  
  0  
#6
Options
Re:Access Point Disconnects After Power Outages
2023-11-30 07:42:25

  @danielpedrosaa 

 

Any updates?

Just striving to develop myself while helping others.
  0  
  0  
#7
Options
Re:Access Point Disconnects After Power Outages-Solution
2023-12-04 11:29:32 - last edited 2023-12-05 05:40:35

Following @Virgo recommendation, I upgraded the firmware on two EAPs while keeping one without the update. After conducting thorough tests, I found that the firmware upgrade effectively resolved my issue.

Recommended Solution
  2  
  2  
#8
Options
Re:Access Point Disconnects After Power Outages
2023-12-05 05:41:25

  @danielpedrosaa 

 

Great! yes

Just striving to develop myself while helping others.
  0  
  0  
#9
Options

Information

Helpful: 0

Views: 1172

Replies: 8

Tags

Mesh Network Connectivity
Related Articles
Access point (Wired and wireless) needed
756 0
Access Point not detected
604 0
Large number of association failures on one access point
417 0
 access point
445 0
 Ethernet WiFi bridge to Access Point Connectivity?
310 0
Home network access point setup help and recommendations
838 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.