Deco x50-poe and x1500-4g setup
Hello all.
My current setup is ISP router into a x50-poe ( all the connections are done by cable ) x50-poe into a POE switch that than shares the internet with 2 more x50-poe units.
I would like to add x1500-4G to the setup as a 4G backup if my cable internet goes bananas.
Can I make it adding the x1500-4g and connecting it to the switch where the main x50 is connected to get power and share internet with the other x50?
Thanks for all
Your help 😀
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi, welcome to the community.
Deco X1500-4G does support 3G/4G backup mode but it only works when Deco X1500-5G is the main Deco, instead of the Deco X50-POE.
How to set up 3G/4G or 4G/5G Backup on Deco router
So now, the current network topology needs to be changed a little bit:
ISP router---Deco X1500-4G---<cable>---POE switch---3*X50-POEs
Thank you very much and best regards.
- Copy Link
- Report Inappropriate Content
i bought the X50-5G, assuming that the X50 line will share all the same Features. Surprise surprise no IOT network is available. The IOT network will be available on the next release ?
- Copy Link
- Report Inappropriate Content
Hi, Thanks for the update.
I noticed you have updated to the 1.2.0 version of Deco X50-5G which has added the IOT network.
By the way, for the CPU usage issue, did it only start after updating to 1.2.0?
Can I have more details of " Blocking my access to the internet"? Would any Deco turn red? Do you need to restart the X50-5G to restore the internet connection?
-By the way, are the 3*Deco X50-POEs still connected to the same POE switch, then to the main Deco X50-5G?
-Could you please email support.forum@tp-link.com with a copy of the web UI system log(please add the forum ID 713618 in the subject, Thank you in advance)?
Wait for your reply and best regards.
- Copy Link
- Report Inappropriate Content
So my setup is x50-5g connected to the router in access point mode, then x50-5g into switch poe that was also 2 in the future 3 x50-poe.
To activate the 4G/5G backup how I do it?
I can’t use bridge mode due to ISP limitation
- Copy Link
- Report Inappropriate Content
Hi, Thanks for the system logs.
Deco in AP mode doesn't support 4/5G Backup and it needs to work in Wireless router mode.
If you can't use bridge mode on the ISP router, I think you could try to disable the WiFi on the ISP router, and then still set Deco X50-5G into Wireless Router" mode.
The recommended topology would be like:
ISP modem router(With Wi-Fi off)---<cable>----Deco X50-5G---POE switch---2* Deco X50-POEs
Wait for your reply and best regards.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@David-TP I also would like to know if I can use the 5G backup on bridge mode. I can always change ISP provider 😊
- Copy Link
- Report Inappropriate Content
Hi, Deco X50-5G can't use 4/5G Backup mode either on Bridge mode. It needs to be worked as the NAT gateway/DHCP router.
Since Deco X50-5G is also a wireless router, maybe you could consider replacing the ISP modem router with Deco X50-5G if the ISP internet terminal has an Ethernet output.
"If I do that, my Deco wifi speed drops from 100 to 1 or 2. So I would say it doesn't work :| Is there something I should configure on the ISP router to allow that configuration to work, besides turning the wifi off ( I already did that)?"
- I think you could also check the QOS settings on the Deco X50-5G when it is in wireless router mode in case it was set to a lower bandwidth.
Best regards.
- Copy Link
- Report Inappropriate Content
Super David, the QOS was what was limiting the internet speed. I will run a few tests. I hope I have no problem with my ISP router
- Copy Link
- Report Inappropriate Content
Information
Helpful: 1
Views: 132
Replies: 9
Voters 1