Home Network Community > Powerline Adapters > Problem with connecting to Tempest Base Station
< Powerline Adapters

Problem with connecting to Tempest Base Station

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Problem with connecting to Tempest Base Station

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Problem with connecting to Tempest Base Station
Problem with connecting to Tempest Base Station
2025-06-10 22:19:50 - last edited 2025-07-07 01:48:28
Model: TL-WPA4220  
Hardware Version:
Firmware Version:

I just installed a new set of TP-Link extenders, previous non TP-Link extenders had stopped working.

 

Trying to reconfigure a Tempest Base Station to use the extended Wifi.
Have two devices and get same result with both.

On trying to configure the Tempest Base Station the Tempest App give network error 1024-07.

 

One post in a tempest forum suggests that the error maybe due to channel being used.
This post in TP-Link forum https://community.tp-link.com/en/home/forum/topic/97039
Suggests that channel can be changed but does not give details.

I see that the two extenders are using channels 2 and 9

 

 

 

Note: Mac where I ran NetSpot is in a different part of the house but I am sure netwok signal strength is not the issue.

 

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Problem with connecting to Tempest Base Station-Solution
2025-06-12 09:34:33 - last edited 2025-07-07 01:48:28

Hi@alktbh,

Welcome to our community.

 

Could I know, is the powerline network working normally? Can other clients work with the powerline network?

If you want to change channel of the extender, please refer to How to customize Powerline ac Extender's wireless settings via web-based management interface (new logo)

 

If the Tempest Base Station was connected the previous network, it is recommended that you can hard reset it and configure it with the powerline network.

 

Thank you.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: △Pre-release Firmware for Archer AX50 Introduces New Parental Control Features and Enhancements △Introducing AI QoS: Elevate Your Gaming Experience on the Archer GE800 Gaming Router △Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN △Tether KidShield Test Recruitment - Safeguarding Children's Online Experience If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
1 Reply
Re:Problem with connecting to Tempest Base Station-Solution
2025-06-12 09:34:33 - last edited 2025-07-07 01:48:28

Hi@alktbh,

Welcome to our community.

 

Could I know, is the powerline network working normally? Can other clients work with the powerline network?

If you want to change channel of the extender, please refer to How to customize Powerline ac Extender's wireless settings via web-based management interface (new logo)

 

If the Tempest Base Station was connected the previous network, it is recommended that you can hard reset it and configure it with the powerline network.

 

Thank you.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: △Pre-release Firmware for Archer AX50 Introduces New Parental Control Features and Enhancements △Introducing AI QoS: Elevate Your Gaming Experience on the Archer GE800 Gaming Router △Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN △Tether KidShield Test Recruitment - Safeguarding Children's Online Experience If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options

Information

Helpful: 0

Views: 311

Replies: 1

About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.