Business Community > All Threads > ACL not work, BUG on TL-SG3428 V2
< All Threads

ACL not work, BUG on TL-SG3428 V2

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ACL not work, BUG on TL-SG3428 V2

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
ACL not work, BUG on TL-SG3428 V2
ACL not work, BUG on TL-SG3428 V2
2021-07-06 22:01:30 - last edited 2022-09-01 02:40:47
Model: TL-SG3428  
Hardware Version: V2
Firmware Version: 2.0.3 Build 20210409 Rel.52950

I tried to create an ACL entry to block a port (TCP 8888) on an IP address (10.10.10.10/32) (because it also not blocked/controlled via the router: ER7206 (TL-ER7206) )

I applied that on all port (or all VLAN) of the switch, but that IP on specific port is still accessible. Settings (only this ACL setting exist on that switch, no other rule or ACL):

 

  2      
 
  2      
 
#1
Options
1 Accepted Solution
Re:ACL not work, BUG on TL-SG3428 V2-Solution
2022-09-01 02:39:58 - last edited 2022-09-01 02:40:02

Hi there,

 

The new firmware TL-SG3428(UN)_V2_2.0.7 Build 20220606 released recently has fixed the ACL-related issue.

 

If you find that Combined ACL failed to block traffic between Layer 3 networks, please check for a firmware update first.

 

Thank you for your attention!

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#3
Options
2 Reply
Re:ACL not work, BUG on TL-SG3428 V2
2021-07-10 13:29:29 - last edited 2021-07-10 13:31:30

@MGergely I tried a Phone call and e-mail about that, but not answered... ACL not work so I also can't block traffics between VLANs...

  1  
  1  
#2
Options
Re:ACL not work, BUG on TL-SG3428 V2-Solution
2022-09-01 02:39:58 - last edited 2022-09-01 02:40:02

Hi there,

 

The new firmware TL-SG3428(UN)_V2_2.0.7 Build 20220606 released recently has fixed the ACL-related issue.

 

If you find that Combined ACL failed to block traffic between Layer 3 networks, please check for a firmware update first.

 

Thank you for your attention!

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#3
Options

Information

Helpful: 2

Views: 2092

Replies: 2

Related Articles
TL-SG3428 V2 ACL don’t work with official FW
855 0
TL-SG3428 V2 - ACLs are not working
676 0
Factory Reset TL-SG3428
2544 1
TL-SG3428 sfp problem
1097 0
Firmware update - TL-SG3428 v2.0
815 0
TL-SG3428 V2 Switch and Omada SDN
1440 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.