Wi-Fi Routers
Update on Jan 16th, 2026: The official version of Archer GE800 V1, 1.3.2 Build 20250929, has been released publicly. Users can check for updates via the router's web interface or through the Tether Ap
Bandwidth Control/QoSWi-Fi 7HomeShieldGaming Router
210Helpful
65352Views
I’m on an 80 Mbps symmetrical fiber plan. My AX12 is connected to the AX53 via LAN and set to AP mode, with QoS enabled, and it consistently shows ~6 ms ping on Wi-Fi. However, when testing directly o
Bandwidth Control/QoS
By
Pankajuuuuu
· Latest post Yesterday
by Joseph-TP
2Helpful
112Views
Just wanted to report an issue after updating my Archer AX55 V1 to firmware 1.5.11. Right after the update, everything seemed fine. But once I enabled QoS, the router basically became unusable. What I
Network ConnectivityFirmware UpdateBandwidth Control/QoSHomeShield
By
Retro_0223
· Latest post Yesterday
by LemonyLime
1Helpful
435Views
As I'm sure many of us are aware, the GXE75 has current issues regarding the Quest 3 / Pro & the 6Ghz channel in the form of disconnections and Ping spikes depending on current firmware. Issues with f
Firmware Update6 GHzMeta Quest 3 (VR)Bandwidth Control/QoSGXE75
6Helpful
468Views
Hello, I have the BE230 v2 EU and am also experiencing this QoS issue, which only makes things worse. As soon as I activate QoS, at 90-95% of my speed, I experience ping shots greater than 1000 ms, Qo
Bandwidth Control/QoS
By
Gamingdave
· Latest post a week ago
by Joseph-TP
1Helpful
357Views
SolutionWhat Can I Do If QoS Enabled Causes BufferBloat and High Latency on My Router After Firmware Update?
This Article Applied to: Archer BE230_V1/V1.20 Archer BE230_V2 Archer AX55_V1 Archer AX55 Pro _V1 Archer AX72_V1 Archer AX72 Pro_V1 Archer GXE75_V1 Archer AX53_V1 Phenomenon: Some users have reported
Firmware UpdateBandwidth Control/QoS
2Helpful
4412Views
I noticed multiple bugs when trying to configure my TP-LINK router. I have a 2Gbps ISP, I've set up QoS to allow 1Gbps/1Gbps and enabled High Priority (which according to the description should remove
2.5 GbpsBandwidth Control/QoS
By
caupatoakosamas
· Latest post 2 weeks ago
by caupatoakosamas
33Helpful
1475Views
I am deciding should I buy Archer C54 My room dropped half its bandwidth by 50%. This is significant loss for my Wi-Fi. When I am outside my room the speed would get around 90~100Mbps. Inside my room
Network ConnectivityInstallationWDS/Range Extender ModeBandwidth Control/QoSHome Setup
By
its_chaudev
· Latest post 2 weeks ago
by terziyski
0Helpful
202Views
Hello everyone, I recently replaced my old ASUS RT-AC86U with a TP-Link Archer GE550, expecting a noticeable improvement in performance and stability under heavy traffic. My main reason for upgrading
Wi-Fi 7Bandwidth Control/QoSGaming Router
3Helpful
1831Views
I’m facing an issue with my Archer C6 router. When I set the 5GHz band to 80 MHz, the upload speed drops significantly. For example: Download: ~97–100 Mbps (normal) Upload: ~15 Mbps (very low) However
Network ConnectivityFirmware UpdateBandwidth Control/QoS2.5 Gbps
0Helpful
161Views
Hi, as the titel says I am experiencing a high amount of packet loss on my internet connection since using the BE9300. I did not have this issue before when I only used the modem/router provided by my
Network ConnectivityBandwidth Control/QoSWi-Fi 7Installation
1Helpful
656Views
I have the Ax3000 Pro model. After updating firmware, ran some bufferbloat tests with QoS on and off. Noticed QoS is broken on this latest firmware. Please refer to pic with bufferbloat testing. Uploa
Firmware UpdateBandwidth Control/QoS
By
David78907
· Latest post 2025-12-05 02:41:12
by Joseph-TP
2Helpful
757Views